chain bed 3d models
160113 3d models found related to chain bed.thingiverse
Anet A8 Chain Bed Protector Remix 200 nozzle - 40 bed - 80% infill - 0.2mm height Remixed from : Xibel Edited by : KoekMaker98
thingiverse
... work with other Y-Axis Chains as well. Use the Flipped version if you put your chain on the right side of the bed. I created this after I notice the chain was coming up above the bed. ...It has a hole cut out underneath for a nut and spring.
thingiverse
I printed the cable chain by papinist and soon found out that the chain can come above the bed when your bed is moving in far top the inside. You can damage your nozzle when it moves over the chain in that position. To keep the chain below the bed I...
thingiverse
when I made my new cable leads, I had printed a few of the stock prusa clamps, some custom one, (about 4-5) and none of them cleared my screw terminals & none had a cable chain connection Designed these in Fusion tolerances for the nuts is a bit...
thingiverse
......Mounting screwed to the bearing bolts. The cables of the original length do not need to be extended. For mounting in the housing, you can drill an additional hole or glue the chain on a double-sided tape or glue. ... Resolution 0.18 Infill 50%
thingiverse
This piece serves for belt protection. ...it will be glued into the rod that guides the spring of the hot bed. ...
thingiverse
cable chain bed cover for stock bed corner.TESTED WORKS. ...
thingiverse
... in the picture. ...I have this on my Tevo Tarantula with a Hictop heat bed. This was made to work with https://www.thingiverse.com/thing:2396718/#comments I initially flipped the motor to the left side then had to move it back after my new bed. ...
thingiverse
... I also cut a small pass-through for the thermistor wire. Note: Print in something that can withstand the heat of the bed otherwise this will warp. I may remix it a bit further and add more support on the cable pass through when I get time. ...
thingiverse
Modified corner for square bed (versus rounded corner bed) Original thing can be found here: https://www.thingiverse.com/thing:2221564 This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/6mKyueB0pFj
thingiverse
Hardware ------------- Regular Cable Chain Bed Mount: • (2) M3x8mm socket cap screws • (2) M3 t-nuts Regular Cable Chain Frame Mount: • (2) M3x8mm (or reuse existing) R18 Cable Chain Bed Mount: • (3) M3x6mm socket cap screws • (2) M3x8mm socket cap...
thingiverse
This is a remix including all parts to create the bed layout. SETTINGS: 0.2 resolution 50% infill no supports no adhesion EXTRA: Time: roughly 8 hours 33 minutes. ... amount: 46 Grams pf filament Type: PLA If you enjoy this help that would...
thingiverse
rear to bed Chain Donate my work: https://www.paypal.me/LpgHof?locale.x=de_DE
thingiverse
My Y chain is on the right so i mirrored and improved this chain protector https://www.thingiverse.com/thing:2221564 to fit the right side of the bed
thingiverse
I really liked the idea of the bed corner piece from the cable chain by johnniewhiskey, but I had already printed out the entire chain from NG_Design... ...so I made this adapter piece to combine the two. ... You need to print out...
thingiverse
My Y chain is on the right so i mirrored this chain protector https://www.thingiverse.com/thing:2221564 to fit the right side of the bed EDIT: I wasn't totally satisfied so I modified the design a little --> https://www.thingiverse.com/thing:3537205
myminifactory
... any. Support me by purchasing through my affiliate link: https://amzn.to/2TInT2O Bill of Materials: 15 x 10x20 Links (Amazon)1 x Bed Link Printed, secure with zip-tie1x Bed Link Cover Printed Optional 1 x End Link (Amazon), secured with zip-tie
thingiverse
The bed end of the drag chain was giving me trouble, so I remade it. This version has the holes for the zip ties in different spots, but should work the same as the original. I fixed some odd geometry and made it a bit easier to print. ... Thanks for...
thingiverse
This is a remix of the part that connects to the bed from http://www.thingiverse.com/thing:1459160 I printed the part included in that link and found that the screw hole in the bed was too far in to the bed for the part. I modified the part to give...
thingiverse
I'm replacing my heatbed springs with 16mm silicone bushings, and needed a new chain protector. ...This is my remix.
thingiverse
On the CR10s the cables from the bed come out much higher on the original fitting. ... This modification adjusts the exit height and added extra strength to the sides.
thingiverse
Designed for this case https://www.thingiverse.com/thing:4071219 I edited the part so a silicon mount collumn would fit better. ...if needed you may need to sand it a bit if the fit isnt right.
thingiverse
Cable chain holder for a bed holder with a bigger distance between the holes. ... Kabelkettenhalter für das bessere Heizbett aus Metall, welches ein größeren Abstand zwischen den Löchern hat.
cults3d
... high flex wire. I am also mounting heat isolation on the bed to protect the cable chain. info: It needs small force to put on the end of the chain on the underside of the bed. and be aware of the sharp corner af the metal! ... Use at own risk!
thingiverse
Main requirement for this to work: your chain must have end segment like on photo (common chain fron china) and this chain must me flexible enough to freely move between surface printer stands on and heat bed bracket Two versions available: left and...
thingiverse
info: It needs small force to put on the end of the chain on the underside of the bed. and be aware of the sharp corner af the metal! Use at own risk! Print Settings Printer: Anet A8 Rafts: No Supports: Yes Resolution: 0,2 Infill: 50 Notes: Before...
cults3d
Among the files there are also larger rollers, in order to better evaluate which dimensions are most appropriate for the length of your cable bed.Together with the rollers of various sizes I have also inserted supports (which must be glued to the...
thingiverse
I had bought a 10x10 cable drag chain in Aliexpress (this one https://es.aliexpress.com/item/Free-Shipping-Best-price-10-x-10mm-L1000mm-Cable-Drag-Chain-Wire-Carrier-with-end-connectors/32369095707.html) so I just needed the male connector. I...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/6KF0dNlFuZS