chameleon antenna 3d models
23201 3d models found related to chameleon antenna.thingiverse
A small protective cover for the Chameleon Antennas CHA Ground Spike. ...I was concerned about the spike scratching or damaging other items in my pack, so this cover just slides on the end to keep the tip of the spike protected.
thingiverse
This is a design for a Chameleon Antenna Wire Winder for your personal use.
thingiverse
3 protective caps for various parts of the Chameleon Antenna System for Ham Radio * Ground Spike protector for the CHA MPAS 2.0 and other vertical antennas systems like the CHA MPAS Lite and CHA TDL. * Antenna connections protective cap for threads....
thingiverse
This enables you to mount antennas to the rear of the Armattan Chameleon.
thingiverse
Just a quick and crazy idea to help in saving antennas hardly mounted on Chameleon frames. ...The idea is quite simple, this piece printed in TPU should smoothly flex and absorb most of the stress transfered to the SMA in normal impacts
thingiverse
Also mounting the RX antennas at 90 degrees angle with one antenna attached to a zip tie on the top plate was far from ideal as every time I removed the top plate, I had to replace the zip tie and shrink tube. So I created this antenna mount that...
thingiverse
Designed to fit Armattan Chameleon 19x4mm arm with 3mm hole for antenna tube. Borrowing the idea of zip tie + heat shrink that I've liked but always had shit luck by having antennas mutilated in props or zip ties breaking off. This tries to fix the...
thingiverse
A tail mount for securing a VTX antenna pigtail and T-style RX antenna on the tail of an Armattan Chameleon frame. ... Printed in TPU at 0.2 (0.3 is ok too) with 40% infill and supports.
thingiverse
This is an antenna tube holder for Armattan Chameleon frame. This will require longer M3 screws. 12mm should do it. I printed this with PLA and 100% infill. ... If you want it to be stronger, you can use v2 which is solid instead of having the cutout...
thingiverse
its tricky to get the activated dipole down the tube but i used tweezers and just pushed it from the hole in the underside if the antenna then slid the full thing down. i also added some strain in the non activated part for cold days when the tpu is...
thingiverse
Armattan Chameleon Ti Antenna Bracket Ver1: 3mm thick Ver2: Adds 2mm thickness to the antenna portion. ...
thingiverse
Here is my Armattan Chameleon UXII Antenna Mount.v2 Made some slight adjustments for better fit of the top plate There is holes for receiver wires based on cable ties. 20mm x 5mm standoffs Slot for LED and hole for cable. ... Printed in PETG 50%...
thingiverse
Print with 100% infill and use flexible filament. ... Its 90 degrees so you have the best possible signal :)
thingiverse
This is an antenna mount for a Chameleon TI. ... It is probably best printed in a flexible filament, it can be printed in PETG or ABS and gently heated to soften the plastic so that the antenna can be inserted through the slots .
thingiverse
Antenna holder replacement for Armattan chameleon TI. The original back-plate has 3 rubbers to mount the antenna tubes and SMA-connector for 5.8Ghz fpv antenna. These rubbers wear out, so I designed this replacement. I printed it in an old roll...
thingiverse
I was having a hard time mounting my receiver antennas in a way that would keep them out of the props, so I decided to design this antenna guide for the Armattan chameleon. Maintains the antenna angle for good diversity performance while preventing...
thingiverse
Armattan Chameleon radio antenna tube mount =================================== * Antennas are placed on the inside to. If you want the antennas on the outside to preserve more space for battery wire, etc, check out...
thingiverse
Armattan Chameleon radio antenna tube outer mount =================================== * Antennas are placed on the outside to preserve space. If you want the antennas on the inside, check out https://www.thingiverse.com/thing:2456683 instead. *...
thingiverse
Front antenna mount/clip for the Armattan Chameleon.
thingiverse
This VTX antenna mount for the PUDA Chameleon fits into the bottom of the rear aluminium standoff, feeds the antenna pigtail out close the base plate of the frame and provides about 30 degrees of up-tilt to the mounted antenna. I'm using it with a...
thingiverse
These mounts are intended to be clipped under the back arms of the Armattan Chameleon frame to hold 3mm antenna tubes, into which you can put your whip antennas so that they don't get chopped by the propellers. At first i had my antennas sticking...
thingiverse
Armattan Chameleon XT60 holder, ELRS antenna, and DJI O3 antenna TPU
thingiverse
A "better" receiver-antenna-tube-mount for the Armattan Chameleon frame. Designed to be placed underneath the rear aluminum VTX antenna mount. Designed to be used with the FrSky XSR Receiver. It should work with the X4R-SB but I have not...
thingiverse
This thing can protect the vtx-antenna when your kwad is getting attacked by trees or bandos. This Thing can be printed with ABS, TPU or even PLA. ...
thingiverse
... the vtx-antenna when your kwad is getting attacked by trees or bandos. ... This version with the sliced hole should be printed with TPU to easily put the antenna in. ... With additional standoffs you can change die SMA Connector into the kwad.
thingiverse
my version of a rear end for the armattan chameleon ti. printed flat with supports. ...the top is ment to hold the power wires secure in place when the top plate is attached and easily removed when top plate is taken off.
thingiverse
Based on duststorm's mount, I modified it to fit on the Feralquads's Fenrir, and any quad that has 26mm standoff distance at the end (Armattan Chameleon...) It has 3mm holes for Rx antenna mounting tubes in "L" shape - the Crossfire version has 4mm.