chell portal 1 3d models

The plate has slots that you can use for tie wraps or you can just use double sided tape. Antenna mount and protector - this will mount and protect a stubby antenna. All parts modeled in Fusion 360. I'm sure some will want to use these as a starting...

This set contains 12 heavily armoured Kingsguard Knights equipped with Greatswords.   Presupported files are included for each model in both STL format and LYS (Lychee Slicer) format so you can rescale them if required.  Presupports have been...

I ended up printing little models of sheep, metal, hay, and trees to represent those cards. *PRINTING INSTRUCTIONS*I highly recommend you follow this guide on reddit to trick your single extruder printer into using a wipe tower. This is...

Print Settings Printer: Folgertech FT5 R2 Rafts: No Supports: Yes Resolution: 0.2-0.3 Infill: 50-70% Notes: Ok, so, I designed the model to be 4 layers thick all around. It needs to be water tight, so, it would be good to let the print run a little...

... in the case. Keeping some tension on the cable while doing so can help.To disassemble, unwind all of the cable, and pop the charging pad out of place by pushing through the bottom hole. Size comparison with the Pixel Watch charger travel case:

If you want to put a thicker piece of paper in the tag without having to adjust the model, you could also try the longer pin. It doesn't take too much plastic to print these, so you could always try it out and adjust accordingly. I put an extra 0.1mm...

I remixed only left side of SethBon's LED Light Bar with 7mm x 8.5mm hole for IR sensor, but the right side is as is.I also created 3 LED strips bar for front and back, plus simple cable guide on the back of YZ plate.Hardware24V LED strip...

[Latest model video](https://youtu.be/-VA2185p2Ro) (Update): We switched brands of K-Cups and discovered that the Amazon brand was slightly smaller, causing it to slip and not cut properly. I edited the gripper ring a third time to add deeper teeth...

I don't have a Flashforge Creator or an equivalent model. I don't want to put a glass plate in my printer that is great for printing PLA and nice if I want to swap out build plates easily for example if I have plates of different materials surfaces...

...Check it out at robotshop.com/ca/en/futaba-spline-metal-servo-horn.html --- A draft CAD model of the FMSH-01 Servo Horn, compatible with TowerPro MG-995 motors, is ready for viewing. It does not incorporate gear extensions or threaded hole features.

If your slicer program doesn't like the single-pass fin at 0.4mm try 0.8 or re-generate the STL from the scad file with whatever thickness you want to try. The whole model is formed from extruded DXFs in OpenSCAD so you can alter them in Inkscape if...

You can then add a line of glue just behind the cabin to finalize the assembly.Then the support parts can be used to mount the body onto my RC car https://www.printables.com/model/281110-rc-car-185-partsIf you use my print files you will see I also...

If you're going to buy them specifically for this model, it's easier to get a Neo Pixel Ring instead. On the photos, you can see that I glued the Neo Pixels onto the LED holder first and then connected them with wires. The 5V power comes directly...

We have found this 0.5 mm thickness to be preferred over thicker and thinner designs, but the thickness can be adjusted as desired by scaling the model in the z direction. The included 2D .dxf file has all curved features defined by continuous arcs...

If you only need the adapter for a drive sled, then you can skip printing this model. The original S-10 drive screws won't work with the riser. You'll have to find some decent fitting self-tapping screws instead (not machine screws). I was just able...

During Thomas Jefferson's management, a new style of peace medal was created which looked like those used by the British, and became the model for the rest of the series. Lewis and Clark took along three large Jefferson medals, 13 medium-sized...

 What I found was that the best way to get a good effect without making it bigger or using more material was to add thickness around the edges of the holes.I wasn't overly satisfied with any of the printable brackets for mounting light...

But-- because of my modeling of the camera's field-of-view,  nothing is visible in the camera's feed. Perfection.New V3 revisionNew V3 design has been strengthened, optimized, rigorously printed, tested and optimized with several different NDs and...

Human: There is a simple way to change the angle of your Apple Wireless Keyboards (Model as pictured). The standard angle is only 6 degrees (approx.) which means the keys are very flat and your fingers need to push down from almost directly overhead,...

For optimal fit, you can modify the lower support to accommodate your phone model. A small USB cable is used for connectivity. Key dimensions include a handlebar diameter of up to 36mm and a stem width of 36mm. Power is supplied by two 18650...

How I Designed This The model was a trick to find. It came from a user forum dedicated to modding flight simulators. I've since lost the URL. I shared the cleaned-up printable version of that a while back. I used Blender for most mesh clean-up and...

I also added a model with an appendage that attaches to bicycle handlebars with zip ties. It's not pretty, but it seems to work OK. EDIT: 5/13/2021 I updated the files. New files have much better fit and some other improvements. The tabs that...

Several scholars believe they served as models or molds for other sculptures. The fact that many, excluding this example, show signs of deliberate mutilation led another expert to theorize that they served a magical function during burial ceremonies...

It took a few model variations and versions and two prints to get right for our specific use case._ --------------------- Backstory: Our clutch split into two, and the basket-mating gear plate has lost some teeth (about at third). With just a clutch...

For fit test purposes, the openSCAD file provides facilities for previewing STL models of the Smoothieboard accessible at http://www.thingiverse.com/thing:290180 and http://www.thingiverse.com/thing:414426. The case was built for use on an 8-inch...

He adapted the hieroglyph of a frontal head and combined it with a frontal torso, modeling the combination as if it were sculpture in the round. His greatest difficulty was with the feet, which are splayed in an unnatural pose. The remainder of the...

Also, these models are a few layers shorter (only 13 at 0.2mm layer height) and have 0% infill, so they should shave an hour off your print time versus the original. In addition to the STEP, Fusion, and STL files for each piece, you'll find...

I named it the ZEPHIR, available in 2 models I made a version for Ender fans;) The principle of this system is to replace the radial fan with a classic 40x40 fan. and the concept of my version is to avoid all the 90 ° bends of the original bulleseye...

... or maybe in Hell, trying to gamble his immortal soul with Leviathan... Special thanks to Guillaume Roos who is the original cube designer. Leave a like if you download and a comment if there's something wrong or right with the model. ...Have fun!

 The compression spring I chose from McMaster-Carr.com is model 9657K608, 0.25" long, 0.210" OD, and comes in a pack of 12 which provides you what you need plus a few spares.  The spring fits in a hole that is 0.125" (3.175mm) deep to...