child locks for drawers 3d models
2319755 3d models found related to child locks for drawers.thingiverse
This is a clone of a simple drawer child lock from IKEA (PATRULL). For some stupid reason, these are no longer available in my country. With careful placement, it can also fit regular cabinet doors. The larger part is fixed inside the...
thingiverse
A simple child lock for locking cupboards and drawers. The child lock is made up of two hooks. One (the one with the flange) is attached at right angles to the drawer front or cabinet door. The hook is designed for the left side (seen from the...
cults3d
As our daughter is growing she can reach higher and higher so I've designed this lock to keep her away from drawer with knives. The IKEA drawer-closing retarder has just enough power to lock the ratchet. ... You need 4 screws to affix it.
thingiverse
As our daughter is growing she can reach higher and higher so I've designed this lock to keep her away from drawer with knives. The IKEA drawer-closing retarder has just enough power to lock the ratchet. ... You need 4 screws to affix it.
thingiverse
Simple and easy to mount lock for IKEA Hemnes drawers. ...The cool thing about this design, is that its only one part and you can easily remove it without remaining holes on painted surfaces.
thingiverse
This is a child lock for kitchen cabinets / doors / drawers. ... You can edit dimensions in online 3d Cad called Onshape: https://cad.onshape.com/documents/447a25d2686103e1641e2763/v/a6d3f2a15b5a9b64b76cf94e/e/2fc4021cbfde664265c37cca There are 3...
cults3d
Well, as the name suggests, it is a stopper to prevent young children from opening drawers. It is recommended to print everything in the same color so that they do not differentiate the different parts, if it is in black better. ... The symmetrical...
thingiverse
I needed a easy child lock for a drawer, that works until the child is too smart. This attaches with a screw and then pivots around the screw protected by the "pin". There is a little bit of a ridge on the back to catch the side of the cabinet and...
cults3d
The Senk-variant is for a door that has a board running on the top of the drawer - it catches onto that, no adhesive catch needed. The SL variant locks drawers to the one above, again no adhesive catch needed. ... To open, pull open to the amount the...
thingiverse
The Senk-variant is for a door that has a board running on the top of the drawer - it catches onto that, no adhesive catch needed. The SL variant locks drawers to the one above, again no adhesive catch needed. ... To open, pull open to the amount...
prusaprinters
I needed a easy child lock for a drawer, that works until the child is too smart. This attaches with a screw and then pivots around the screw protected by the "pin". ...There is a little bit of a ridge on the back to catch the side of the cabinet and...
thingiverse
... Infill: 25% Notes: The distance between hole centers is 65mm. I designed this knob to use M3 screews, with accommodation for M3 nut.
thingiverse
These prevent "lever" style door knobs/handles from being pulled down, they can only be pulled up to open the door. ...There's a slot for a captive M4 nut and a single bolt to clamp down on the handle.
thingiverse
... Print one latch and one catch for each door. There are two different lengths available for the latch (1.5" and 2.5") and a 1/4" spacer that can be used for fine adjustments. ... Recommended print settings: 0.3mm layer height 100% infill no support
thingiverse
... safe against children. For suggestions, problems or other things you wanna tell me, write in the comments and i look into it. ... I printed with an Anet A8 with 1.75mm PLA on 0.3 layers (0.8 walls) on 200 °C extruder and 60 °C bed temperature
prusaprinters
The purpose of this print is to lock the drawer of the IKEA ELLOVEN, so it can't be pulled all the way out, when you just want to get something from the drawer.Prints on the side, I used PLA but probably you can use anything.Attach one of the clips...
thingiverse
Modified commercial child lock. Elegant non intrusive HARD TO OPEN design. ... There are different versions of upper cap: 1) rounded -you will need support to print it 2) flat- no support needed I also attached 2 versions of limiter: 1)...
pinshape
Modified commercial child lock. Elegant non intrusive HARD TO OPEN design. There are different versions of upper cap: 1) rounded -you will need support to print it 2) flat- no support needed I also attached 2 versions of limiter: ...
cults3d
Modified commercial child lock. Elegant non intrusive HARD TO OPEN design. There are different versions of upper cap: 1) rounded -you will need support to print it 2) flat- no support needed I also attached 2 versions of limiter: 1) Ready to...
thingiverse
Child safety lock for cabinet or shoe rack. ...Left and right part
thingiverse
child safety lock for cabinets. snap in place. ...designed for my specific cabinets knobs are spaced 2" and the shaft of the knobs are .348" long by .405" dia
thingiverse
This is a lock mechanism to use with drawers or a closet door for child safety. Just print without supports like in the last photo shown. Then use a screw to combine the lock with the latch part and add a rubber band to lock the mechanism. ... To open...
prusaprinters
A simple spacers used for more stability on Nuki locks.Printing instructions:no supports needed
thingiverse
Drawer locks for my drawers in my camper van. ...A simple design but very effective.
thingiverse
Because only you know, from the outside, where the lock inside is, and the fact that you need magnets to "unlock" it, no one else, at least without watching you, would know how to open it properly. I deigned space for two of 2mm*5mm...