cigarette case for roll ups 3d models

PETG 0.5

A roll up cigarette case that’s simple and hardwearing. I designed this case because I was struggling to find a case without hinges (that would probably break) or without any silly symbol or logo on the front. Case holds between 12-15 roll ups and...

That didn't work well since i needed to carry my tobacco and filters with me for rolling 'em up because i couldn't carry pre rolled ones. So i fumbled around with openscad some more and this is the result. Now i can pre roll some and won't go over my...

I printed the original desing but it was too short for my cigarettes, so I made a new one myself basing on the original desing (I didn't modify the original, I did it from scratch). I also made the lid a little bit looser because when I printed the...

This is a simple cigarette case. ...It can set 8 hand roll cigarettes of 8mm in diameter and 70mm in length. ... Pitch : 0.2mm Material : PLA Infill : 20% Small Case Short Case Tobacco Case

... the process. Therefore, I scaled it down to accommodate two cigarettes, making it more compact. Additionally, I extended the lid by a few millimeters to ensure a better closing. ...I printed it using a 0.6 nozzle and a layer thickness of 0.32.

This is a box I put together for his that will hold up to 12 rolled cigarettes. The lid is friction locking and the hinge has a 3mm hole. ...I just cut a nail for the pin and used a dab of crazy glue at one end to keep it from falling out. Edit: Added a...

My father rolls his own cigarettes and he asked me for a case to hold them. Rolled cigarettes are slightly fatter than commercial ones and are a bit longer. This is a box I put together for his that will hold up to 12 rolled cigarettes. The lid is...

CIGARETTE CASE FOR SELF-ROLLING + KINGSIZE

It's a pocket case for holding four tubes of filters (only available in the UK?), a spare pack of papers and a space to hold four pre-rolled cigarettes. Designed using Fusion 360 and sliced with Slic3r. As I said, this is my first attempt...

Small cigarette case for hand rolled cigaretes - max 73mm long Magnetic lock. Contain holes for 5x8mm neodymium magnets. Print Settings Rafts: No Resolution: 0.2-0.3 Infill: 10 Notes: CIgarette case Because models are high i suggest to use brim. Also...

This is a cigarette case. ... I designed it for a slim type cigarette, and engraved rose

This desing It was created for shorts cigarettes

Cigarette case for 20 filled tubes (8.5mm diameter x 85mm long). I printed it without supports and there have been no more problems than some loose thread inside. Nothing serious. It is my second own design, and the first one that I decide to...

This thing was made with Tinkercad. ...All you need is a piece of wire for the hinge. 2 dividers to hold 6 cigaretts in each of the 3 pockets. ... I need to make a latch of something, next rev.

Should print fine. Haven't printed it myself yet only an earlier version. Remodeled everything with nicer code in openSCAD. Edit anything if you like... edit: there are two new versions of this but since the edit files upload button isn't working i...

In the vastness of the Internet, I did not find a suitable case for me to use pwnagotchi with ups-lite and decided to do it myself. Printed on an SLA printer for a better result. When you type, I ask you to share with me the result, suggestions...

This is a cigarette case. ... I designed it for a slim type cigarette, and engraved rose image on the center of the body part. ...

TOBACCO BOX OR CIGARETTE CASE FOR ROLLING CIGARS OR INDUSTRIAL CIGARS. ... ONE AREA FOR PAPER AND MOUTHPIECES AND ANOTHER AREA FOR ROLLING TOBACCO.

Case for e-Cigarette : 2 battery's 3 mod or clearomiseur A V2 is here : http://www.thingiverse.com/thing:544363

Cigarette case for 4 cigarettes with lid

Case for a cigarette pack. Convenient, practical, original. You no longer need to look at the terrible pictures on the pack. You can use ready-made inserts or make your own. It does not require print support. Use 0.8-1.0 mm wire for the hinge axis.

Case for a cigarette pack. Convenient, practical, original. You no longer need to look at the terrible pictures on the pack. You can use ready-made inserts or make your own. It does not require print support. Use 0.8-1.0 mm wire for the hinge axis.

A Cigarette case for 100's, I have included the skp file so you can resize it for normal size cigarettes. Also I have added a place for your fingers to go so you can slide the lid on and off as it is quite tight. To make this work well for me i...

This is a remix of this rolled cigarette case https://www.thingiverse.com/thing:536620 I fixed the scaling so it works out of the box with regular cigarettes, plus some space for hand rolled. ... I also included a handy size_test object for figuring out...

... provider has. I bought simple 12V UPS module and attach 18650 battery to it. And now I have possibility to keep power on my router. There is a case for this simple device. ...Note, you will need the six nuts which should be inserted in the holes

Customized version of https://www.thingiverse.com/thing:536620 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=536620

Customized version of https://www.thingiverse.com/thing:536620 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=536620

Cigarette case for self-rolled cigarettes 70 mm long. ...With a cigarette diameter of 8 mm, it holds 10 pieces

Just made it a little bigger to accommodate 100s and home rolled cigarettes.