circular fan 3d models
121173 3d models found related to circular fan.thingiverse
This is a Circular Fan Duct for "Hypercube 300 Lite X Carriage" made by user: adrianm1972
thingiverse
This is a Circular Fan Duct for "Hypercube 300 Lite X Carriage" https://www.thingiverse.com/thing:3316565
thingiverse
Semi Circular Fan Duct Unit (SCFDU) ! It features * compatibility for Jayko Industries Titan Aero Mount ! * astonashing airflow * easy use * compatible for Anet A8 default 50mm Turbo fan ! * shorter neck for more comfort and less colissions...
thingiverse
This part was remixed from the offset circular fan duct. This one is centered, however it is a bit short on my printer but the space between the duct and my heater block I found acceptable. ...Print Settings Printer: Alunar...
thingiverse
Alternative circular fan duct for Tevo Tornado printer. Works quite well with PLA however ABS or any higher temp resistance material recommended. ...
thingiverse
It keeps the air pressure constant and it acts as the semi-circular fan duct regarding air pressure. It has a small offset and it just avoids the heating block. ... https://www.thingiverse.com/thing:1954001 ...
thingiverse
Circular fan duct based on http://www.thingiverse.com/thing:69557 modified to allow for a 40mm fan. Fits Bukobot 8 V1 (pre-"spitfire" extruder). M3 screws fit, but are a bit tough to thread in due to scaling of the back of the mount when it was...
prusaprinters
Circular fan duct based on http://www.thingiverse.com/thing:69557 modified to allow for a 40mm fan. Fits Bukobot 8 V1 (pre-"spitfire" extruder). M3 screws fit, but are a bit tough to thread in due to scaling of the back of the mount when it was...
thingiverse
Was trying to make a dual fan full circular part cooling fan duct but it didn't work well because of the space around the extruder on Anycubic 4Max So I ended up with this, I am not sure if it is better than the semi circular fan duct I posted...
thingiverse
I found that all of the circular fan ducts for the Anet A8 are angled/off-center from the fan output to the circular section. On my Alunar M508, the geometry between the cooling fan output and the heater block is straight-on, so round Anet A8 ducts...
thingiverse
------------------------ This is a circular fan duct with low profile (no bed scratching) for LK4 Pro or U30 Pro printer. The ring part was taken on other design on thingiverse : https://www.thingiverse.com/thing:1823404 I made this to have a...
prusaprinters
DescriptionA Circular Fan Duct adapted for the Anycubic 4Max Pro. I tested many fan ducts here in Thingiverse, no one reached a better quality then this one!.Get your own picture of the results.How to PrintJust print it with your optimized parameters...
thingiverse
# Description A Circular Fan Duct adapted for the Anycubic 4Max Pro. I tested many fan ducts here in Thingiverse, no one reached a better quality then this one!. Get your own picture of the results. ### How to Print Just print it with your...
thingiverse
Use "fan blower.stl" UPDATE: I've updated design with: - better fan mount (angled for clearance and visibility) - improved internal flow (reduced complexity) - improved printability (it now prints with less support when placed on its side, and uses...
prusaprinters
Use "fan blower.stl" UPDATE: I've updated design with: better fan mount (angled for clearance and visibility) improved internal flow (reduced complexity) improved printability (it now prints with less support when placed on its side, and uses less...
thingiverse
... print around. Even the bottom of the fan holder can knock into the print because it is so low This is a mountable fan duct for the Lulzbot TAZ. This is useful for improving the quality of PLA prints. ... It requires 4 heat set nuts and 6 m3 bolts.
thingiverse
Things I changed from the original design by Ahasuerus: increase size so that it fits 50mm fan instead of 40mm increase size of the center space to allow for the larger Bukoschnozzle heater block (ID now 33mm) cut out an area on the topside to allow...
thingiverse
As my hotend is not centered in the carriage (I'm using Greg's accessible extruder: http://www.thingiverse.com/thing:8252), I have adjusted this fan duct design to short it in 4mm (use on the left side of the carriage). I have also added a clearance...
thingiverse
A Circular Fan Duct adapted for the Anycubic 4Max Pro 2.0.
thingiverse
Anycubic Mega S - Circular Fan Duct. ... Can be printed without supports.
thingiverse
This is a circular extruder fan duct I designed for the Unified Prusa i3 mount by inornate http://www.thingiverse.com/thing:1277720, derived from Bunjatec's original circular fan mount.
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/gvH5T7KDOTA modified semi circular turbo fan duct to block airflow to nozzle
thingiverse
Update: 2015-8-11 solidwork source file uploaded A improved Circular fan duct. --This should be used with the retainer from thing:451667. --The Aluminium block‘s position need to be adjusted to avoid touch the fan duct. 2mm space is enough. ...--Cut off...
thingiverse
WIP Had issues with overhangs, not being printed nicely at the back of the models, so I wanted to try with circular fan duct. Couldn't find one, built one on my own. I printed it vertically, using tree support, build plate only. ...I also used brim...
cults3d
For those who want to use a circular fan and a BlTouch sensor at the same time on a MK8 i3 Extruder. ...Successfully sliced with Cura 2.3.1 and printed with Anet A6 for a Geeetech Prusa i3 pro B.
thingiverse
For those who want to use a circular fan and a BlTouch sensor at the same time on a MK8 i3 Extruder. Successfully sliced with Cura 2.3.1 and printed with Anet A6 for a Geeetech Prusa i3 pro B. ...Print Settings Printer: Anet A6...
thingiverse
... pointing holes and hole front/centre removed to spread the air flow around. A Circular Fan Vent for printing with PLA on the Rapide Lite. ...You probably will need to print your own connector piece to join this to the existing part blower fan vent.
thingiverse
I have found that with many circular fan ducts the nozzle is not even close to being centered...so I created this one. In addition i tried designing the inside so that the filament is cooled equally from all sides. ... Eventhough the ring is quite...
thingiverse
This is the circular fan duct, with extra mounting holes to mount to the side of the Open X Carriage, for those few of us who haven't moved to a Prusa. The top of the funnel is also lowered so as to make room for the belt catch tab. ...