cl 260 3d printer
1842019 3d models found related to cl 260 3d printer.thingiverse
... into the adjustment screw holder on CL-260. Additional parts: M3x20 screw M3 nut & washer magnet 5mm dia x 5mm length Print Settings Printer: CL-260 Rafts: Yes Supports: Yes Resolution: .4mm nozzle, .2mm layer height, 4 perimeters Infill: 25%
thingiverse
Another Simple Power Plug in for the CL-260.
thingiverse
Simple Power Plug in for the CL-260. ...Fitting for this: http://de.aliexpress.com/item/Promotion-3-Pin-IEC320-C14-Inlet-Module-Plug-Fuse-Switch-Male-Power-Socket-10A-250V/32652015558.html?spm=2114.13010608.0.112.CdZnEd
thingiverse
With this you can convert the CL-260 3D-Printer in to a dirackt drive Printer.
thingiverse
First thing I made to solve a real world problem: How to mount the heat bead relay of my CL-260 3D printer? ...Print Settings Printer: CL-260 Rafts: No Supports: No Resolution: .4mm nozzle, .2mm layer height Infill: 15% Post-Printing Use M3x5mm nylon...
thingiverse
Better Extruder Design for the CL 260 3D Printer or other Printers. Fast Flexfilament printing is possible with that extruder. I print TPU with PLA speed. It is also able to print with inconsistent (diameter) Filaments. (!!! Need to be scaled down...
thingiverse
This is a replacement carriage for the CL-260 3d printer. It uses 12mm OD bearings from McMaster rather than the stock 11mm OD bearings that came with the original part (which I couldn't find easily). The bearings are kind of short, so I used 2 per...
prusaprinters
Better Extruder Design for the CL 260 3D Printer or other Printers. Fast Flexfilament printing is possible with that extruder. I print TPU with PLA speed. It is also able to print with inconsistent (diameter) Filaments.</p> <p>(!!! Need to be scaled...
thingiverse
LED strip mount for cl-260 printer. ...Use M5*8 screws.
thingiverse
Tons of more features, more hardware support improved acceleration values For Cl-260 printer, RAMPS 1.4 and A4988 (standard for this printer) or TMC2100 drivers and standard display If you get heating failures, buy a better PSU or run PID-Tuning ;)...
thingiverse
Sliding block with built in belt tensioner for CL-260 Printer. which is Chinese knockoff of Ultimaker, and looks similar to alumimaker. http://www.aliexpress.com/store/1828072 with 8mm axis rods with 11mm copper bushings. use M3 bolt for tensioning.
thingiverse
... after lapping the sleeves !Under shaft 6 mm http://ali.pub/35xt10 This is an improved version, I stopped at it, I believe that this is the end of my work ! https://3dtoday.ru/shop/detali-dlya-3d-printerov/chasti-printera/cl_260_ultimaker_2/
thingiverse
I asked Langwei for the original STL files for the CL-260 that were printed in PLA. ... Here they are so you can reprint them in ABS or PETG, etc Print Settings Printer Brand: RepRap Printer: Think3d Rafts: No Supports: Doesn't Matter Resolution: .2
thingiverse
... for these covers. Print Settings Printer: CL-260 Rafts: No Supports: Yes Resolution: 0.2 Infill: 50% Notes: Motor mount corner can use higher infill (70-80%). Print once Non-motor corner twice mirrored, once not mirrored. ...Top cover times four.
cults3d
I asked Langwei for the original STL files for the CL-260 that were printed in PLA. ... Here they are so you can reprint them in ABS or PETG, etc
thingiverse
Eine Leiste zur Befestigung von 25cm langen LED-Streifen am CL-260. Klebefläche steht im 30° Winkel zur Horizontalen und Übergangsstücke an den Ecken verstecken die Verbindungskabel. Die Leiste ist insgesamt 29cm lang und passt diagonal gerade so in...
thingiverse
Axisholder for the CL-260 ------------------------------------ This replaces the original axisholder. They are for 15mm linear bearings (I'm using the plasic IGUS ones) Sources ------------ The FreeCAD files are on the git repository: ...
thingiverse
Teile für direkt extruder von flexibler Welle angetrieben (kompatibel mit compact head 11mm):https://www.thingiverse.com/thing:2691910 CL 260 Ultimaker UpGrades Upgrade parts for the CL 260 and similar printers The page is under construction and can...
thingiverse
CL 260 ! Это улучшенная каретка ! Максимально упрощена ! Более эффективно , из всех что я видел ! Нарисована с целью избавиться от люфта и брякания ! Качество печати значительно улучшилось, в паре с головкой-кареткой экструдера ! ...
thingiverse
https://www.youtube.com/watch?v=WTN-0OF16Fw CL-260 Головка экструдера,каретка под вал 6мм ! В общем были разные идеи,пробовал на графитовых втулках,покупал хорошие линейные подшипники LM6UU с валом ! Измазёкивал валы кусками литола ! Не получалось...
thingiverse
# CL-260: Carrier for E3DV6 # License: GPL-2.0+ -- GPL Version 2.0 or later. Copyright 2018 Tobias Frost <tobi at coldtobi.de> This program is free software; you can redistribute it and/or modify it under the terms of the GNU...
thingiverse
here are now the facts about this carriage - 1 used 2 LM8UU bearings for the carriage, which has an outerdiameter of 15mm - There is no holder for an cooler fan for the printed stuff, i print on this printer only ABS and dont need it. ... - Its...
thingiverse
original firmware from seller. ...(edit) 2018/21/1 This firmware is not for 2018 or higher version of cl-260! this firmware is for 2016-version of cl-260 it can be used for reference purpose. Print Settings Printer: cl-260
thingiverse
The factory STL files for the CL-260. The seller sent me these to fix some parts. ... They have since closed the store and not available.
thingiverse
A simple cover for the carriages of the cl-260 that prevents the falling off of the round bars.
cults3d
Hello. ...This thing is a part of stock extruder on CL-260. ...This is a fitting holder on mk8 extruder.