cl1 3d models
114 3d models found related to cl1.thingiverse
A minimalist clip to hold the Sony MP-CL1 pico projector. ...Uses a 1/4-20 thread to mount on camera tripods.
thingiverse
Built for the Rotor Riot CL1 frame using the Lumenier AXII 5.8 stubby. 25mm tall so you can use shorter standoffs. ... Mounting holes are 22mm apart
thingiverse
- 30 degree Hero8 mount - 30 degree Session mount - Front bumper - Arm guards - Long range antenna mount (gps/sma/immortal) - SMA/RX antenna mount Prints are available for purchase here: https://bmc3d.co/products/rotor-riot-cl1-accessory-set
thingiverse
Standard GoPro Mount that will screw to the front four screws of the Rotor Riot CL1 chassis.
thingiverse
Official Rotor Riot Accessories =========== These are the official accessory STLs for the Rotor Riot CL1 FPV Drone Frame: https://rotorriot.com/products/rotor-riot-cl1-frame Some parts from the HD1 will work on the CL1 too! They are the same parts...
thingiverse
do solid infill. best out of a hard rigid plastic like abs or pla. stick it with some double sided tape and go power slide. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/iN9DW185VeE
thingiverse
Customized version of http://www.thingiverse.com/thing:384919 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=384919 Instructions Using the following options:...
thingiverse
I made this for the CL1 frame with 20MM standoffs. itll fit the standard 30MM standoffs too. Print TPU at 20-30% infill, and use supports. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/6uPLOeZZ4zz
thingiverse
This works with the Rotor Riot CL1 frame, and would likely work with others. You will need a M5 nut, or find one from a broken GoPro mount. It works in the front or back, 32 or 33mm spacing. I used 8mm M3 screws to replace the 5mm ones holding the...
prusaprinters
This works with the Rotor Riot CL1 frame, and would likely work with others. You will need a M5 nut, or find one from a broken GoPro mount. It works in the front or back, 32 or 33mm spacing. I used 8mm M3 screws to replace the 5mm ones holding the...
thingiverse
Just a simple rear mount for a VTX antenna for the CL1 frame by rotor riot. I made this since my frame had no way of mounting the antenna. I used a cheap TPU and the fit onto the frame is noice and snug. No fear of this sliding up and down the...
thingiverse
a mount for the hero8 with polarpro filers on a rotor riot CL1
thingiverse
TBS Tracer antenna mounts for the Rotor Riot CL1, with sma mount with the mounting holes.
thingiverse
Arm Bumber for the CL1 Frame which also soft mount the motors. ...Print 2 regular and 2 mirrored with flexible filament.
thingiverse
I couldn't find an antenna mount for the Rotor Riot CL1 VS Frame, so I changed this mount for the Wizard X220HV by JohnnyFFM to fit the Standoff distance of the CL1. Since it's open to put the antenna in, better secure it with a zip tie, just to...
myminifactory
This is a 30 degree GoPro Session mount for the Rotor Riot CL1. Print on its side for best results. ... Please ignore errors in the print, still working out a few problems with TPU on my printer.
thingiverse
GoPro mount for Rotor Riot CL1 frame. Printed in TPU at .2mm Layer. You may want to trim the small cross piece in front. ... Screws are a little tight but with a little pressure the fit in.
thingiverse
This is a 30 degree GoPro Session mount for the Rotor Riot CL1. Print on its side for best results. ... Please ignore errors in the print, still working out a few problems with TPU on my printer.
thingiverse
This is a gopro mounting accessory for the rotor riot cl1 frame. ...I have tested printing it in pla and tpu and both work however pla is much more prone to breaking and vibration issues.
thingiverse
Standard (30mm I think) standoff rear mount for TBS antenna on Rotor Riot CL1 frame. This made of TPU and allows for a swift 3mm screw mount (thats flexible upon crashing) for TBS antenna that has built in taps for 3mm thru-screws. The...
thingiverse
An adapter to let you replace the mediocre DLP in the Gakken Worldeye spherical projector with a Sony MP-CL1 or MP-CL1A laser pico-projector. You'll have to take apart the Worldeye almost fully to get to the lens and the mounting screw bosses for...
thingiverse
40mm fan duct to upgrade the Cliever CL1 Black Edition 3D Printer. This solves the issues with small details and small bridges that limits this printer. Can be mounted with the hotend cover. At the photo I was just testing. ... Update: Totally...
cults3d
Designed for Sony's new MP-CL1 laser pico-projector, this printed plastic holder makes installation quick and easy. It is equipped with a flexible part to avoid scratching the shell of the pico-projector. Its ultra-flat profile makes it easy to...