clamp on music sheet holder 3d models
1442872 3d models found related to clamp on music sheet holder.thingiverse
This is a portable sheet music holder which I have designed for my daughters flute lessons. The arms can be fold away. Tip: Try out GCode Simulator to check your print upfront On Thingiverse: http://www.thingiverse.com/thing:44286GCodePrintr - 3D...
prusaprinters
This is a sheet music holder that uses exposed honeycomb infill, with several perimeters for strength.The base uses an overhang that's pretty extreme, so supports may be needed, or a little sanding if printed without supports. ... PLA probably...
prusaprinters
This is a portable sheet music holder which I have designed for my daughters flute lessons. The arms can be fold away. Tip: Try out GCode Simulator to check your print upfront On Thingiverse: http://www.thingiverse.com/thing:44286 GCodePrintr - 3D...
cults3d
A simple sheet music holder for my girlfriend's Yamaha P45 Piano. It should fit other - maybe ? ... Very simple design / simple to print.
thingiverse
A simple sheet music holder for my girlfriend's Yamaha P45 Piano. It should fit other - maybe ? ... Very simple design / simple to print.
thingiverse
This is my sheet music holder for my electronic drum set. It clips on the horizontal beam. ## Construction - Put the printed screw into the holes on the stand and on the support piece. - If the hole is too rough for the screw to be inserted, you...
prusaprinters
A simple sheet music holder for my girlfriend's Yamaha P45 Piano. ...It should fit other - maybe ? Very simple design / simple to print. Print Settings Printer Brand: Prusa Printer: I3 MK3SRafts: No Supports: NoResolution: 0.2 Infill: N/A Category:...
thingiverse
This music holder is flexible to hold as little as one sheet of music or a few hundred pages of a book. You'll have to modify the thick end unless your stand is right around 11mm thick. For books that refuse to stay open you may need two. If I was...
thingiverse
A simple Ukelele holder to hang it on a sheet music stand Fits on the 16 mm stem of the sheet music stand Ukelele 35 mm wide and 25 mm deep
thingiverse
this stand allows you to hold your tablet on top of your sheet music shelf. ...
thingiverse
Very simple holder that snaps on the sheet music stand of my digital piano Roland FP-10 and prevents the sheets from falling down. I'm confident it will fit other piano brands as well. I recommend printing in PLA so that they can bend slightly...
thingiverse
A clamp to replace broken originals for the Haron Sandpaper Sheet Holder. ... Clamp width is 93 mm with a 5 mm hole in the centre.
thingiverse
Simple cable holder to clamp on any desk top surface or similar. ... Fusion 360 included so you can change dimensions.
thingiverse
This is a cup holder that clips on to my clamp. ... https://www.thingiverse.com/thing:3531386 I also have a phone stand that clips onto the same clamp Phone Stand https://www.thingiverse.com/thing:3569519
thingiverse
Remix of the stock filament holder that comes with the ender 3 S1, Simply clamps onto the side of your desk. ... Ideal for stacked printers on shelving
prusaprinters
Simple cable holder to clamp on any desk top surface or similar. Fusion 360 included so you can change dimensions. Category: Electronics
thingiverse
A remix of the original clip part from Music Sheet Holder https://www.thingiverse.com/thing:395243 to make it adjustable for different table/shelf sizes. ...
thingiverse
... your desk so you don't spill your drink on your valuable stuff. ...4 inches in diameter. Can easily fit any cup. Update: For the cup holder part, print the corner parts with higher infill to prevent the splitting of layers as you clamp down on stuff.
thingiverse
I added to the original long clamp frame clamp allowing it to be a headphone holder. ... Be sure to use the long frame knob.
thingiverse
It's just a drink holder designed with soda cans in mind that clamps to a table. ...Enjoy.
thingiverse
This is a remix of the Clamp-on Cup holder by Seth_aka_Seth. The original design does not allow to place cups in it, so we create a space where the handle of the cup could be placed. ... If you like this design you can support us by buying some...
thingiverse
This is a remix of the Clamp-on Cup holder by Seth_aka_Seth The original was a little too low poly for my liking so I remixed a smaller one to hold a standard sized soda or beer can. ... Enjoy
thingiverse
Mashup of the Tiko Hanging Spool Holder and Small Clamp. Take a look at those postings for hardware and assembly info. ... In addition to the parts listed there this clamp uses an EZ-Lok M5 heat press brass threaded insert Printer: -- Eustathios...
cults3d
Mashup of the Tiko Hanging Spool Holder and Small Clamp. Take a look at those postings for hardware and assembly info. ... In addition to the parts listed there this clamp uses an EZ-Lok M5 heat press brass threaded insert Printer: -- Eustathios...
thingiverse
Requires 3x 8-32 machine screws and nuts. ...Clamps onto lawn mower with 7/8" handle.
thingiverse
Use 2 M5 bolts with nuts to clam this spool holder on the edge of the work bench top with a maximum thickness of 20 mm. The spool holder works with the filament reel with 32 mm center hole. ... Print Settings Rafts: Doesn't...