clean nozzle ender 3 v2 3d models

Simple BL Touch mount for Ender 3 V2, using 2 pcs M3 Screw STL parts are pre-orientated for easy print and good results Additional parts needed : M3x6 Button Head/ Hex Screw 4 Pcs M3 Nut 2 Pcs Probe offset for the firmware: X-42,Y-5 Original Creality...

Also my calipers didn't fit right :) My model is tested with Ender 3 v2 only, without the right side display, because mine has been moved to the left. ...Also, my printer is raised because of the improved cooling, otherwise the whole thing would be too...

A screen cover for the Ender 3 V2. To keep the dust off it when not in use. Because I use OctoPrint, I rarely need to see the screen and my work area is quite dusty. Has a knob for easy removal, and has the Ender logo I have included the FreeCAD...

A screen cover for the Ender 3 V2. To keep the dust off it when not in use. Because I use OctoPrint, I rarely need to see the screen and my work area is quite dusty. Has a knob for easy removal, and has the Ender logo I have included the FreeCAD...

Solid feet for the Ender 3 v2, problably other Enders/printers as well, fits all 40x40 profiles. 43mm high, 20mm wide, (20x20mm wide at the bottom). I made these to make room for larger PSU and Motherboard fans. Remove the orignal rubber feet...

This is a divider that will fit in the larger section of the drawer under the bed of a Creality Ender 3 v2. Each segment has it's appropriate size etched into the bottom. ... I bought this kit on amazon:...

I wanted a filament guide that could fit over the filament holder on my Ender 3 V2. This is something I put together on TinkerCad quickly to do that. ... If you want to tweak it or play with it then you can find the original over on...

Este es una adaptacion de este modelo https://www.thingiverse.com/thing:5260591Los eslabones no son mios, El credito de los eslabones es unica y exlusivamente de https://www.thingiverse.com/arek_r1/designsLo unico que hice fueron unos pequeños...

Turns out in the upgrade to the Ender 3 v2, they used a new part for the beeper which is a lot smaller than the original. So I replicated the design with the new sizes. ... The upper section cannot be any thicker (which would increase the sound...

Feet for ender 3 v2. They will give you extra 15mm ground clearance. They do not stick though, so if you lift the printer up they will fall. Also the rear left leg would normally colide with the psu cover, because of the hook for the cables. ...I have...

Ender 3 V2 Tension Caps Cap #1 goes in the front facing slot Cap #2 goes in the slot above the LCD screen May be a little snug, so you may have to wiggle the legs a little to loosen them

Turns out in the upgrade to the Ender 3 v2, they used a new part for the beeper which is a lot smaller than the original. So I replicated the design with the new sizes. ... The upper section cannot be any thicker (which would increase the sound...

After making Ender 3 v2 ikea lack, I wanted to take the motherboard out and made a simple drawing compatible with the motherboard in Fusion 360. I used a fan size of 80x80mm in a drawing. ...cover screw holes were created for 3mm bolts.

Designed up this Ender 3 V2 LCD Support to move it closer to the body and save space on printer place. ... Printing: Print it in horisontal with supports (minor needed) with 50 degrees touch base only PLA (20% infill) 210º Extruder 60º Base ...

mod for original spool holder and my feet 35mm 35 mm feet feet: https://www.thingiverse.com/thing:4699997 bottom mainboard for noctua 40x40x10 with 2 stepdown lm 2596 https://www.thingiverse.com/thing:4684550 fan 60x60x25 noctua fan grid...

This is some feet I made for my Ender 3 v2 because I did PSU and Mainboard covers for better fans and needed more clearance space underneath. ... They will raise the printer 30mm See also PSU cover for 80x80x25 fan: ...

Este es una adaptacion de este modelo https://www.thingiverse.com/thing:5260591 Los eslabones no son mios, El credito de los eslabones es unica y exlusivamente de https://www.thingiverse.com/arek_r1/designs Lo unico que hice fueron unos pequeños...

(Updated STP included) Full Stl file of ender 3 v2. Used for reference to do addons so you can see what your printer will look like before printing addons. By using tinkercad ect. ...you can now see your machine in full before printing the actual...

Simple feet to adjust/level your printer, it fits the standard rubber feet of the Ender 3 v2. I use them with these risers https://www.thingiverse.com/thing:4665097 . It gains plenty of space for ventilation beneath the Printer. ...There is one version...

Filament Arm for Ender 3 V2: -will keep your filament away from the leadscrew -no support needed -no bed adhesion needed -10% infill is enough -friction fit (dimensional accuracy differs per print/printer, i am not to blame if it doesn't fit well)

This is a 53.5 mm diameter dial gauge holder for the Ender 3 V2 printer. It sits on top of the extruder fan housing and attaches to the extruder with an M8 x 25 mm screw. The bracket is of the clamp type. ...For the comparator there is a M6 x 60 mm or...

Webcam mount for Ender 3 V2 I used this HD Camera with Ringlight from Amazon Remark: You can open the camera at by removing the white light ring and adjust the focus. You only need to remove the glue on the thread. ... Category: 3D Printer Accessories

FOR/ PARA --- ENDER 3/pro/v2 not big deal its a filament guide no need screews yust plug and play ball bearing needed 7.9mm inside 22mm out ------------------------------------- no es la gran cosa es una guia para filamento colo colocar y usar se...

Seamlessly add two USB A ports to your Ender 3 V2. Attaches to the left of the power cord beneath the y-axis motor at the back of the machine via the power socket mounting screws. Simple wiring and easily removable. ...Actively cooled by power supply...

I did found one similar model, but it was way to small - couldn't push them on extrusion and rubber feet didn't fit also - so I amde my own :)  For ender 3 v2 users: remove PSU (black) cover, the PSU will become cooler and then the feets...

Yet another fan guard for Ender 3 V2. I use it alongside my fan duct: https://www.thingiverse.com/thing:4754118 The inside cone is particularly wide to correspond to my front remplacement fan that has quite a wide center disk (12mm). ...I'd suggest...

Super Basic part to cover the screen on the new Ender 3 V2. Parts rest on the outer frame of the screen not the screen itself. ...I have both the plain screen cover and the cover with imperial logo that I printed for myself here.

... the way, so I made this. ...It is mountable on the Ender 3 V2, and I'm not sure about the pro. Definitely not the original, though. It is made for the raspberry pi 4b. ...Thanks to https://www.thingiverse.com/thing:4665097/ for making this originally!

Filament guide using a pulley (with bearing) to minimize friction for Ender 3 V2 that clamps to the frame using M3 screws. ...The filament guide does not depend on any other accessories and works with dual gear or single gear extruders that have...

Webcam mount for Ender 3 V2 I used this [HD Camera with Ringlight from Amazon](https://www.amazon.de/dp/B08YX55WC2?ref_=cm_sw_r_cp_ud_dp_VGQF1DPNG9E97YB366FK) Remark: You can open the camera at by removing the white light ring and adjust the focus. ... ...