click and grow 3d models

First of all, credit where credit is due: This is basically a mash-up from https://www.kevsrobots.com/blog/pistands.html and https://www.kevsrobots.com/blog/self-watering-plants.htmlThis is a stand for the Pimoroni Enviro...

Print Settings: Printer: Anet a8 Rafts: Doesn't matter Supports: No Resolution: .15 Infill: 100 Notes: This model prints flawlessly without supports, producing extremely thin yet remarkably strong and flexible cups. They are perfect for holding...

I bought a knockoff Aerogarden by Moistenland, which works great, but finding the replacement grow baskets are impossible. The Aerogarden baskets are slightly larger than the hole in this one and look kind of awkward. This version came together...

The Grow Pod XL, designed with nature's simplicity in mind, showcases life's delicacy and highlights the value of our food. Available as a single 3D-printed transparent polyjet piece, it aims to inspire healthier lifestyles. ...Check out @devinsidell on...

The designer created a hook system using shelf's honeycomb holes to hang grow lights, suitable for Lights of America brand grow lights or similar ones with keyhole connections. A Plano model 9524, 4-shelf unit serves as the tested shelf unit. Round...

These clips, designed to hold 6.8mm fibreglass rods in a grow tube frame, come in two types: one with a hole entirely through it and another with a hole only two-thirds of the way through as an end stop. In testing, gales reaching up to 140km/h gusts...

The whole fan duct is 205mm wide so you need to check that it wide enoughto cover the whole of the vent in your grow tent, the ones on my tent are approximately 180mm wide. If you don't want to use M3 heated inserts, send me a message i can...

This is a grow Tent Stand featuring the following dimensions; Length: 182mm Width: 150mm There is also a supporting arm underneath the tray making this as sturdy as possible. This was mainly used to put a mini dehumidifier on this platform at an...

... you. ...Here is the rewritten text: Made for infinityhacker1998. Check out his 3D requests at https://www.reddit.com/r/3Drequests/comments/hh9jha/grow_tent_clips/. ...Support his work with a donation via PayPal at www.paypal.me/infinityhacker1998.

... rods for framing grow tubes at garden bed corners. ...They offer increased stability, given they face prevailing winds. Previous clips were challenging to install near corners, but these new ones provide a sturdier and more straightforward solution.

This allows you to plug the holes in your "Lettuce Grow" The print consists of two parts that can be glued together. ...If you want to save printing time you can just print the plug part without the handle and it will still work correctly.

... printed Grow tent corners, designed to accept 1/2inch schedule 40 pvc. ... Use to add support poles for a trellis or just to keep the tent sides from sucking in. 2 version's, 1 for a vivosun 16mm tent pole and the other for AC infinity 22mm tent pole.

I reimagined Knape's iconic Super Mario World Fire Flower by stripping away its facial features and embossing the word GROW into the flower's center, leaving the base intact as a testament to its original design. ...I employed TinkerCAD to bring this...

... ... This is to prevent light on the top of the sponge and reduce the mildew / mold growth from the top of the sponge.  It may have been only me getting this but it stopped when I put a tin foil sheet over the sponge. ... This looks a little nicer.

... this 80mm fan duct because all I could find was 120mm fan and I need one smaller to fit on my printer. ... I printed it I have yet to actually use it as I'm waiting for the fan so I don't know if it will move enough air out of my grow tent. ...

This is a small grow light shell that sits about 85mm high. ...I used three single neopixels and single core wire. There is a cavity to push wires through to the inside of the "lamp shade". ...I had to print with supports.

Unbolted the 30cm lengths from the strips and crafted clips and supports using old plywood, wire bits, and some creative problem-solving. Now all I need is permission to install it from the boss... ...Supports required for the hanger doughnut were...

This system is used to germinate and grow vegetables and other plants inside using LED grow light (Search Amazon BOBL3FHXQG0) panels and incorporates a variable speed fan (Search Amazon BOBG4CCR4V) to circulate air and harden off the plants as they...

Used grow light led strips . ... Epoxy coating to avoid leakage from reservoir.

Clips on to poles of Vivosun (or any grow tent with 16mm poles).

This is a pod for Bosch Grow Systems. ...I have printed mine without supports.

Efficiently cultivate greens using ECO Grow, a Solidworks-based method that optimizes plant growth.

I'm not sure whether peeling the skin off the seed is worthwhile - comment below if you managed to grow one and how you did it! Printer Settings: Brand: Printrbot Model: Printrbot Plus Rafts: Doesn't Matter Supports: Doesn't Matter Resolution:...

... slide them in. You don´t need to glue them. There are two drains for excessive water on the bottom.Fill the starter with potting compost and place the plant seeds close to the glas pane. Keep it moist and watch the seeds starting roots and grow.

... them in. You don´t need to glue them. There are two drains for excessive water on the bottom.Fill the starter with potting compost and place the plant seeds close to the glas pane. Keep it moist and watch the seeds starting roots and grow. 

Printing the Grow planter on a BQ Prusa i3 Hephestos with 0.2mm layer height and 1.75mm Hatchbox PLA filament at 200°C proved to be a huge success. Note that there are two distinct parts: the main planter itself and the water collector, which is...

Crowley, the notorious demon from Good Omens, this 3D-printed masterpiece is here to turn your potted pals into thriving botanical wonders.Equipped with a sturdy stick, this quirky creation can now be effortlessly plunged into the heart of your...

The bracket can be tightened and will fit around 16 mm poles securely. I designed multiple versions. For smaller printers, the frame was split from the hinge which can be attached using strong super glue. Two M3 x 16 mm bolts were used to attach...

Needed a way to hold a florescent grow light I already owned a few inches above my seedlings as I try my hand at growing some bonsai plants. ...I printed each stand in just over an hour.

Pole bracket mount for Sunbeam Blizzard oscillating fan for use in a grow tent. Clips onto a 16mm tent pole. ...