clip on bed shelf 3d models

Clip your phone on a shelf and charge it

... I used the clip from jgreene777's insulin pen vent clip (great idea by the way) and I designed the rest of the little shelf to fit my BMW 535xi. It should fit about any vent with enough width. ... I hope someone else finds it useful as well!

Just want to find a phone stand that can clip on a shelf but I can't. Then I make my own and start with goralski's table cloth clip. Thanks, goraski. ...Simple modifications with Tinkercad.

Just want to find a phone stand that can clip on a shelf but I can't. Then I make my own and start with goralski's table cloth clip. Thanks, goraski. Simple modifications with Tinkercad. ...

It has been broken up into 4 pieces to fit on smaller print beds and clips together. The "Full" file is all 4 pieces together for those that have larger printers to print as a single piece. The small pockets on the left side are 40mm X 36mm. The...

I needed a shelf to hold a wifi camera that didn't have a standard camera mount.

I designed and printed this on my CR-10 to hold my Asus TransformerBook on my shelves so that I could control my printer via Octoprint from the tablet.

I created this shelf to clip on to the $10 filament shelf so that the filament shelf could hold more than filament. One of the cool ways to print this is without top and bottom layers (see image) and with 10% gyroid infill. Without these settings...

... ... Raised bed used is a galvanized 6x3x1FT metal one, on this clip snaps in place on the top lip of the walls. This allows for a rabbit fence to be pulled alongside the bed wall and keeps it close enough so that rabbits won't be able to slip through.

Clip on bed tray for the Ikea svarta loft bed. Remixed from typicalcow's thing. Print sideways with tree supports, takes around 14 hours to print on an ender 3 v2 5% cubic infill is sufficient for speed and rigidity I added the holes for the string...

Should work on other beds as well with simple adjustment of dimensions.http://www.ikea.com/us/en/catalog/products/80253814/ Instructions Print upside down to avoid need for support material. Print bottom separately and glue on. Make sure that the...

I made this to allow me to clip a fan onto the side of a bunk bed in the summer. This is to fit a 20mm side.

I remixed this one for my old Microsoft Nx 6000 for D6 or Monoprice Ultimate 3d printer. ... Support needs for those webcam which just need to clip on will works too. ... was rush to use it, support not even remove yet.

The shelf is designed for a bed board of approximately 16.5 mm. ...But there are sources, you can increase or decrease the size which is shown in the screenshot.

This gravity spool holder is for me the best spoolholder for Prusa MMU2S system. I just tried to improved it with a new clip which allow to secure the spool holder on the shelf. ...Now, the spool holders cannot move and slip during the print</p>...

The beveled clips (for the side of the head) I positioned on the outside of the shelf, where the brush also found its place. I just did not want to put the power supply there (due to the hanging cable). The font I have later changed (in...

This is a Clip On Hook that is 5mm wide for 3/4" Wire Rack Shelves.

This is a Clip On Hook that is 5mm wide for 1" Wire Rack Shelves.

This is a Clip On Filler Spool Holder Brace for 1" Wire Rack Shelves. Look in my Spool Holder Collection at https://www.printables.com/@brass_ring/collections/713739 and https://www.thingiverse.com/brass_ring/collections/38795236/things to see my...

This is a Clip On Filler Spool Holder Brace for 3/4" Wire Rack Shelves. Look in my Spool Holder Collection at https://www.printables.com/@brass_ring/collections/713739 and https://www.thingiverse.com/brass_ring/collections/38795236/things to see...

Shelf of tubular superposed bed of 20 in diameter. we move it as we like, fix a lamp etc .... ... #DAGOCULTS

I searched and checked many clips for heat bed but all have the same problem or brings new one.  I found Jolly_Oli's Ormerod Heatbed clip but still it was big and useless for Wanhao i3. I inspired and redesigned it for Wanhao i3 with shorter footage...

Hello everybody I made this shelf for my Ikea bed with 29mm side thickness. This bed shelf has 3 parts: 2 mounts and plate. I use small screws because plate can be built with another material, for example cut plywood by laser. Plate has 5 mm...

... If you have mounted your glass plate on top of the aluminum plate see my thing called Glass Plate Bed Clip for Glass Plate on Aluminum Plate. ...See my blog at http://thekoalafarm.blogspot.com/ Instructions i use 6 clips to hold my glass plate on.

A small bedside shelf, fits iphone 12/13 mini perfectly. ...

If you have mounted your glass plate on top of the PCB see my thing called Glass Plate Bed Clip for Glass Plate on PCB. See my blog at http://thekoalafarm.blogspot.com/ Instructions i use 6 clips to hold my glass plate on. ...I've included the Cubify...

I always had trouble with bulldog clips and in cases pause, home all, or printing anything over 160 x 160 mm Fan unit kicks the clips and have bed leveling problem immediately. I searched and checked many clips for heat bed but all have the same...

it is designed to be used on a corner of the bed using binder clips on two sides in order to securely attach it. At 100% size the mount is 10mm thick to accommodate screws of various lengths.***** I highly recommend that if the mount is being placed...

Bed mount for the Creality Sonic Pad G-sensor so Y-axis input shaping can be tested. ...Attachable with binder clips.

... Place the calibration block between the clips of the indicator and hold up against the bottom of the top support bar to zero the indicator. Remove the calibration block then move the bed/build plate back and forth to check for adjustments needed.