cobb accessport v3 vent mount 3d models

Cobb Accessport mount to vents with supplied accessport mount

This is for the Cobb Access port, no ball bearing needed. ...Just use this to slide the access port as a vent mount

Subaru WRX side defroster vent mount for the Cobb Accessport. Did not need any additional hardware. Just pops right in and holds the accessport snugly. Tested on 2018 WRX model. This is an ongoing project. Check back for updates soon! ###...

This is a holder for your Cobb Accessport V3. It attaches to your ac vent. Its much better than trying to use adhesive tape. The _lp "low profile" is V2 and sticks out less from the dash. ...Print Settings Printer Brand: ...

This is a replacement ball mount for the COBB Accessport. Print two and cement together, no supports are needed. I recommend 5 or more perimeters and a rigid, heat-resistant filament. ...FreeCAD file is included.</p> Category: Automotive

This is a replacement ball mount for the COBB Accessport. Print two and cement together, no supports are needed. I recommend 5 or more perimeters and a rigid, heat-resistant filament. ...FreeCAD file is included.

This is a 2015+ WRX defroster vent mount for a Cobb Accessport remixed from dasfruit. I added vent fins, enclosed the portion of the mount around the cable holder, and added a clip to keep the cable from coming out of the mount. I also added tabs...

I designed this to adapt Cobb-Accessport style mounts to hold my phone. I designed the phone-mount portion to fit my iPhone X in its case, so it's unlikely that it will work for other people. It's designed to be assembled with M3x4mm low-profile...

Universal roll cage mount for Cobb Accessport. ... -Includes two sizes (40mm/1.57" and 44.45mm/1.75") -Universal vehicle fitment -Retains your factory magnetic cradle included with the Accessport -Will require hardware x4 - M5 x 12mm Screws (MCM* -...

I built this so that it attaches tightly to your side pillar plastic and has a ball for the socket on the AccessPort mount. Feel free to dice and slice this to your hearts content. It was built for function, not prettiness. Best printed in...

A mount for a v2 accessport for my 2010 STI. Double-sided tape alone does not work well enough, use a small zip tie to anchor the mount to the dash. No modifications to the dash are required, the knurl the zip tie end a bit and cram it into the gap...

... adhesive, sand and paint as desired. ... Remix of thing 3542130, utilized contoured section from that thing and re-created a more sturdy mounting mechanism, suitable for left-hand drive STs. ... Print one of each "arm", and clamp, and two "mounts"

I found this inventive vent clip: https://www.thingiverse.com/thing:3880775However, it's intended for right hand drive Focus MK3 ST and RS models.Since I'm in the US, I sliced up the mount in Tinkercad, mirroring the asymmetrical portion for it to...

... This vent mount perfectly matches the fit and finish of the OEM vent and makes installing your Accessport super simple. This mod is perfectly reversible and will not harm the original parts. The factory defrost function works perfectly still.

Replace the factory dash defrost vent in your 2002 - 2008 Subaru Forester SG / XT and mount your Cobb Accessport. Includes the LH and RH versions with .stl and .step files No hardware is required. Simply pop out the stock vent and this will clip...

Replace the factory dash defrost vent in your 2007 - 2014 Subaru Impreza WRX/ STI and mount your Cobb Accessport. Check photos to make sure this is the correct part for your car. Includes the LH and RH versions with .stl and .step files No...

It is a two-piece print that utilizes the cradle that is included with the AccessPort V3. This print took a lot of tweaking to get the fit perfect for my vehicle so it may not fit properly since all printers are slightly different. Try increasing or...

Customized version of https://www.thingiverse.com/thing:322859 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=322859

(thanks!) It's been flipped for US/left-hand drive, and modified to use the new mount design for the accessport holder. works great, though it's hard to get both sides clipped in. I've found the rubber molding around the door holds one side in...

... you can rotate it easily, so the longer part of the visor can block incoming sunlight better. I prefer the center vent location, next to the cupholder (in a 04 WRX) This part will work with V2 and V2B AccessPORTs, regardless of vehicle application.

I created this STL file as a free simple fix to a known issue with the Cobb Accessport cable breaking it's original tabs. Leave a comment if this helped you or if you run into any issue with printing these. If you need this part 3d printed and do...

This is a holder for the Cobb AccessPORT that can be used to mount it to the vent grille to the left of the steering wheel on a Subaru WRX. Definitely works on the '02-03 WRX, might work for later models. The cord clip allows you to unplug the AP...

The 90 degree bracket is probably the easiest solution however is limited to flat areas, the ball joints offer the original mounting capabilities of the v3 mount but with a right angle! Bracket is intended to be used with double sided mounting...

Adjustable Cobb Tuner Mount For Subaru Impreza STi (2008-2014) Also fits Forester XT (2003-2007) Features: 175° adjustable base mount 2 point adjustable locking arm Optional slot or ball-socket mount point Vent slots that mimic stock vent...

Customized version of https://www.thingiverse.com/thing:322859 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=322859

This AccessPort mount lets you mount your device above the light switch without blocking it. It allows the most surface area possible so the double sided tape is less likely to come loose. ... I have been using this for 6 months now and it holds even...

This is Reeseallen's design including v4.3 of the holder and v3.6 of the clips condensed into 1 layout. ... Instructions Print, then use acetone or superglue to attach the clips to the holder.

If your cable release clip is broken here is cheap solution to fix it so you do not need to buy new cable.

This replaces the driver side vent pod by firmly but evenly pulling the OEM vent out of its socket and firmly pushing this into its place.

The accessport is a great tool. ...I have created a clip for the A piller that worked well but it stuck out in my vision. I wanted something a little more discreet. This clip allows a clip in to the vent and cable to run through the air vent. ...