cobb accessport wrx 3d models
715 3d models found related to cobb accessport wrx.thingiverse
This is a 2015+ WRX defroster vent mount for a Cobb Accessport remixed from dasfruit. I added vent fins, enclosed the portion of the mount around the cable holder, and added a clip to keep the cable from coming out of the mount. I also added tabs...
thingiverse
Subaru WRX side defroster vent mount for the Cobb Accessport. Did not need any additional hardware. Just pops right in and holds the accessport snugly. Tested on 2018 WRX model. This is an ongoing project. Check back for updates soon! ###...
thingiverse
This is a holder for the Cobb AccessPORT that can be used to mount it to the vent grille to the left of the steering wheel on a Subaru WRX. Definitely works on the '02-03 WRX, might work for later models. The cord clip allows you to unplug the AP...
cults3d
Replace the factory dash defrost vent in your 2015+ WRX/STi with a custom vent that can hold your Cobb Accessport in an easy-to-reach and view location. No hardware is required. Simply pop out the stock vent and this will clip back in its place.
cults3d
Replace the factory dash defrost vent in your 2007 - 2014 Subaru Impreza WRX/ STI and mount your Cobb Accessport. Check photos to make sure this is the correct part for your car. Includes the LH and RH versions with .stl and .step files No...
thingiverse
This is Reeseallen's design including v4.3 of the holder and v3.6 of the clips condensed into 1 layout. ... Instructions Print, then use acetone or superglue to attach the clips to the holder.
thingiverse
Cobb Accessport mount to vents with supplied accessport mount
thingiverse
This is a replacement ball mount for the COBB Accessport. Print two and cement together, no supports are needed. I recommend 5 or more perimeters and a rigid, heat-resistant filament. ...FreeCAD file is included.
prusaprinters
This is a replacement ball mount for the COBB Accessport. Print two and cement together, no supports are needed. I recommend 5 or more perimeters and a rigid, heat-resistant filament. ...FreeCAD file is included.</p> Category: Automotive
thingiverse
This is a holder for your Cobb Accessport V3. It attaches to your ac vent. Its much better than trying to use adhesive tape. The _lp "low profile" is V2 and sticks out less from the dash. ...Print Settings Printer Brand: ...
thingiverse
This is for the Cobb Access port, no ball bearing needed. ...Just use this to slide the access port as a vent mount
thingiverse
... you can rotate it easily, so the longer part of the visor can block incoming sunlight better. I prefer the center vent location, next to the cupholder (in a 04 WRX) This part will work with V2 and V2B AccessPORTs, regardless of vehicle application.
thingiverse
I created this STL file as a free simple fix to a known issue with the Cobb Accessport cable breaking it's original tabs. Leave a comment if this helped you or if you run into any issue with printing these. If you need this part 3d printed and do...
thingiverse
I designed this to adapt Cobb-Accessport style mounts to hold my phone. I designed the phone-mount portion to fit my iPhone X in its case, so it's unlikely that it will work for other people. It's designed to be assembled with M3x4mm low-profile...
cults3d
Universal roll cage mount for Cobb Accessport. ... -Includes two sizes (40mm/1.57" and 44.45mm/1.75") -Universal vehicle fitment -Retains your factory magnetic cradle included with the Accessport -Will require hardware x4 - M5 x 12mm Screws (MCM* -...
thingiverse
Tired of the sticky ball joint you get in the case with your Cobb AccessPort. I built this so that it attaches tightly to your side pillar plastic and has a ball for the socket on the AccessPort mount. Feel free to dice and slice this to your...
thingiverse
A mount for a v2 accessport for my 2010 STI. Double-sided tape alone does not work well enough, use a small zip tie to anchor the mount to the dash. No modifications to the dash are required, the knurl the zip tie end a bit and cram it into the gap...
cults3d
Replace the factory dash defrost vent in your 2002 - 2008 Subaru Forester SG / XT and mount your Cobb Accessport. Includes the LH and RH versions with .stl and .step files No hardware is required. Simply pop out the stock vent and this will clip...
thingiverse
(thanks!) It's been flipped for US/left-hand drive, and modified to use the new mount design for the accessport holder. works great, though it's hard to get both sides clipped in. I've found the rubber molding around the door holds one side in...
thingiverse
Due to limitations with the sheet metal used on the stock Cobb SF air box for the Subaru wrx, there is a decent size gap between the intake and the top of the air box (2-3 in^2). This part will line up with the current fasteners and provide a...
thingiverse
Remixed this off Jasonjones's design, thanks Jason. Added some curves to prevent it digging into the dash and added screw holes to add some adjustability. recommend using some pads on the inside of the grip to help it grip. Use PETG or ABS to...
thingiverse
Print in PETG/ABS at high temperature for good layer adhesion Assemble with solvent based adhesive, sand and paint as desired. Remix of thing 3542130, utilized contoured section from that thing and re-created a more sturdy mounting mechanism,...
thingiverse
If your cable release clip is broken here is cheap solution to fix it so you do not need to buy new cable.
prusaprinters
<p>I found this inventive vent clip: <a href="https://www.thingiverse.com/thing:3880775">https://www.thingiverse.com/thing:3880775</a></p><p>However, it's intended for right hand drive Focus MK3 ST and RS models.<br><br>Since I'm in the US, I sliced...
thingiverse
Customized version of https://www.thingiverse.com/thing:322859 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=322859
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: font_size = 10 hole_radius = 3 font_thickness = 5 stick_width = 8 message = WRX stick_thickness = 3 Font = write/orbitron.dxf flat_bottom = 2
thingiverse
Customized version of http://www.thingiverse.com/thing:548191 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=548191 Instructions Using the following options: thick =...
thingiverse
Customized version of http://www.thingiverse.com/thing:548191 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=548191 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:305087 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=305087 Instructions Using the following options:...