cocoon create touch 3d printer i3
2968470 3d models found related to cocoon create touch 3d printer i3.thingiverse
Print Settings Printer: wanhao i3 Rafts: Doesn't Matter Supports: No Resolution: 0.20 Infill: Solid Fill Notes: Left and Right sides. Print Base layer on build plate for structural strength (for screwing into wood base), you need maximum crush...
thingiverse
... the binding/jamming of filament on the reel as the reel gets to the end. ...It clips easily over the top rail of the printer and holds securely on its own. ... I've flattened one side, so print on its side without supports and it will print cleanly.
pinshape
To celebrate the Australian Duplicator i3 / Cocoon Create / Wanhao / Balco Facebook group reaching 100 members and the new Cocoon Create Touch I made a mini version. Most items are simple prints that don't need supports. The spool holder may...
thingiverse
... 5mm spacer to lift the spool holder so that the larger spool cleared. You may need to replace the two screws with slightly longer ones if the ones included with your printer are too short. Made for Cocoon Create Touch/Wanhao Duplicator I3 Plus.
thingiverse
print3Daus made a really tidy brace for the Y-axis idler of the Cocoon Create Touch / Wanhao i3 Plus. However, apparently there have been some revisions to that part. His idler holder was a plastic injection moulded part, whereas the y-idler...
thingiverse
A LED strip holder for the Cocoon Create Touch (i3 Plus clone). I use a rear mounted cooler so the factory fan mount is not used. ... No screws needed just slides on the bracket You will also need a 600ohm resistor Material required: One ...
thingiverse
This is the Cocoon Create Touch / Wanhao Duplicator i3 plus Z Axis Brace mod I created from using this video as a guide. I have uploaded the individual STL files from those creations. https://www.youtube.com/watch?v=Xxr2GkDVfV8 As mentioned in the...
thingiverse
07/04/18: Uploaded adjusted version with 0.2mm tolerance (originally 0.1mm) Z screw stabilizer for Wanhao i3 Plus To install, 1. Undo the plastic clips in the gantry which holds the ribbon cable 2. Undo and remove all screws securing the top part...
thingiverse
... mounts to the bracket with some M3 x 12mm screws. Once it's all installed, then the cover clips over the top to hide the cables. This cover is also open at the back, so you can touch the extruder connectors and make sure they aren't getting hot.
prusaprinters
I prefer this style because if the set screw ones come loose, then many of them are impossible to access without some printer disassembly. There are two styles. One with an open end, and one with the end capped off. ...The capped ones may help prevent...
thingiverse
I prefer this style because if the set screw ones come loose, then many of them are impossible to access without some printer disassembly. There are two styles. One with an open end, and one with the end capped off. The capped ones may help...
thingiverse
I'm not sure that the Cocoon Touch even needs a MOSFET because of the lack of compatible brackets, however, given the similarities to the Wanhao I3 Plus, I'll go out on a limb and say that at least adding the MOSFET shouldn't make it any more unsafe....
thingiverse
These are Just some simple fan covers I made to stop my kids jamming there fingers in the fans, just a push fit into the fans holes that don't have screws. ... Sliced using Simplify 3D
thingiverse
Slimline Raspberry Pi 3 Model B case to attach to Wanhao Duplicator i3 Plus and clones: * Wanhao Duplicator i3 Plus * Cocoon Create Touch * Balco 3D Touch * Monoprice Maker Select It is designed to mount the Pi what you could consider back-to-front,...
prusaprinters
If you need to place your spool holder for Wanhao Duplicator i3, Cocoon Create, Maker Select, and Malyan M150 i3 3D printers, (designed and tested for Wanhao Duplicator i3 assumed sameness) somewhere other than the top or controller box. print on a...
thingiverse
If you need to place your spool holder for Wanhao Duplicator i3, Cocoon Create, Maker Select, and Malyan M150 i3 3D printers, (designed and tested for Wanhao Duplicator i3 assumed sameness) somewhere other than the top or controller box. print on a...
thingiverse
--------------------- # Configuration that worked for me in doing filament change in octoprint https://www.reddit.com/r/wanhaoi3/comments/gi7tqy/configuration_that_worked_for_me_in_doing/ ## Requirements: * https://github.com/andrivet/ADVi3pp...
thingiverse
Mosfet and Extruder Carriage pcb mounting plate. ...Screws into the factory holes on the Cocoon Create right z axis frame. ...Make sure to use standoffs between parts to prevent shorts.
thingiverse
Our friends over at "3D Printer Wiki" have also put together a build guide for this mod: http://3dprinterwiki.info/wiki/wanhao-duplicator-i3/duplicator-i3-basic-mods/z-brace/ If you get a redirect: try going to http://3dprinterwiki.info/ and...
cults3d
Our friends over at "3D Printer Wiki" have also put together a build guide for this mod:http://3dprinterwiki.info/wiki/wanhao-duplicator-i3/duplicator-i3-basic-mods/z-brace/ If you get a redirect: try going to http://3dprinterwiki.info/ and clicking...
thingiverse
Modified the Teaching_Tech_camera_mount_-_base_-_prusa_i3.stl with Fusion 360 to allow it to fit my Monoprice Maker Select Plus horizontal gantry. ...Clips on the top of the frame
thingiverse
Sorry for the terrible photos, but I'm not taking the printer out of its enclosure for photographing the parts. :D Requires a 20 - 25mm m3 bolt and nyloc nut. As per AlexWYYC's design, you may need to rotate your extruder motor so the wires...
thingiverse
The frame is designed to take a 3mm PMMA half enclosure for the front of the printer to help stabilise temperatures for ABS printing. The rear half will be up in the next few weeks along with the enclosure specs. The frame is meant to separate the...
thingiverse
Glass bed holder for Cocoon create and wanhao duplicator I3 v2.1 bolt holders into position and place a thin piece of high density foam between glass and holder and gently squash as you lower the opposite end of glass bed into the opposite holders
thingiverse
Made for the Cocoon Create Touch for the front mount where the original fan is mounted. will need to mount your blower fan at the back if you want to use this. there is a 2-3mm play area where the shaft will touch the bed. i used 15mm allen head...
thingiverse
This is a duct to be used on the Cocoon Create Touch with the mounting bracket from Gascat's High Performance cooling assembly: https://www.thingiverse.com/thing:2084339 The original duct couldn't quite reach the heating block on the CT so I made...
thingiverse
Geared Bondtech extruder for the Cocoon Create Touch/ Wanhao I3 Plus. This extruder uses the existing heatbreak, in my case the Micro Swiss all metal heatbreak. I wanted to try the geared Bondtech drive, but did not want to have to purchase another...
thingiverse
Cocoon Create Touch Spool Holder - With Bearings. Description:- Included is the SketchUp file for you to tweak / improve on. Bearing Placement:- I oversized the holes for the bearings. To fit them wrap sticky tape / duct tap around them,...
thingiverse
Hey Guys this is another mod for Wanhao Duplicator I3, Maker Select, and Cocoon Create 3D Printers. this time its a filament guide. i have found this very helpful to direct the filament where it needs to go. No non 3D printer parts are needed, your...
thingiverse
I have seen a number of feet for the Wanhao but it seems the steel plate on mine (Balco touch) is a little thicker. I measured it at 2mm. These feet print well and have helped me to level the printer. ...Also, the desk it lives on is not flat so this is...