coin battery holder 3d models

Coin battery holder - Designed to fit 2 x 1216 3V Batteries. ... Made in Solidworks and easy enough to modify.

This coin cell battery holder uses a minimal amount of filament to store CR2032 batteries. The batteries snap into place and will remain in the container even when held upside down. There's a thumb slot to help remove the batteries, and an engraving...

remix of "Remixed Customizable Coin Battery holder" with low profile sides to allow easier grasp of coin battery cells. you can configure count (amount of battery cells), coin cell radius and thickness. ... default for CR2032 has 20mm diameter and...

Simple holder for CR2450 battery

This is based on my CR2032 coin cell holder design, but the following User Parameters changed: cell_diameter = 20mm cell_thickness = 1.6mm See the original model at https://www.thingiverse.com/thing:2859523 for Fusion360 source file. ... If you don't...

This is based on my CR2032 coin cell holder design, but the following User Parameters changed: cell_diameter = 16mm cell_thickness = 3.2mm See the original model at https://www.thingiverse.com/thing:2859523 for Fusion360 source file. ... If you don't...

This is based on my CR2032 coin cell holder design, but the following User Parameters changed: cell_diameter = 20mm cell_thickness = 2.5mm See the original model at https://www.thingiverse.com/thing:2859523 for Fusion360 source file. ... If you don't...

Simple but sturdy storage for 10 CR2025 coin cell batteries.This is based on my CR2032 coin cell holder design, but the following User Parameters changed:cell_diameter = 20mmcell_thickness = 2.5mmSee the original model under “This remix is based on”...

Simple but sturdy storage for 10 CR2016 coin cell batteries. This is based on my CR2032 coin cell holder design, but the following User Parameters changed:cell_diameter = 20mmcell_thickness = 1.6mmSee the original model under “This remix is...

A small holder for 10 CR2032 coin cell batteries. Update 12/22/2017: Added Fusion 360 export with some user parameters to adjust for different sizes and number of coin cells. The original version (the one without a lid) fits a bit tight when putting...

Like thing http://www.thingiverse.com/thing:21041 but customizable. ...So you can select the number of coin batteries to put in it, and what type of coin battery.

This is a holder for a coin cell battery. There is one for a single battery and one for a double battery. A stripped, 20 Gauge wire can be used to provide the electrical contact. One wire is weaved through the holes on the bottom (-) and another...

This is based on my CR2032 coin cell holder design, with the following User Parameters changed:cell_diameter = 16mmcell_thickness = 3.2mmSee the original model under “This remix is based on” for Fusion360 source file.If you don't have a 3D printer...

Surface Mount Battery Holder for CR1632Memory Protection Devices Inc. ...(MPD)http://www.batteryholders.com/part.php?pn=BU1632SM-JJ-GTR

Holder fits in a typical small parts tray.  Each holder holds 30 batteries, separated for each other so that they do not short out.

... http://www.thingiverse.com/thing:79259 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=79259 Instructions Using the following options: sizedivider = 0.4 custom_radius = 10 nr = 5 custom_width = 3 battery = CR2032

Hi, I made a batteryholder for CR2032 thats easy and fast to print. ... It needs no Infill, so you can print it with 2 wall lines (0,4mm nozzle). The batteries are very easy to remove but you can turn the container arround and they wont fall out.

http://www.thingiverse.com/apps/customizer/run?thing_id=79502 Instructions Using the following options: custom_radius = 10 radwire = 0.6 battery = CR2032 build_plate_manual_y = 100 build_plate_manual_x = 100 rack_dist_y = 15 rack_dist_x = 12 edge =...

http://www.thingiverse.com/apps/customizer/run?thing_id=79502 Instructions Using the following options: custom_radius = 10 radwire = 0.6 battery = CR2032 build_plate_manual_y = 100 build_plate_manual_x = 100 rack_dist_y = 15 rack_dist_x = 12 edge =...

Coin battery holder for two CR2016 batteries. ... I printed these to have as part of my Everyday Carry (EDC) as replacement batteries for my car's keyless entry remote.

... the games. ... None of the designs I found worked very well, the LED's came loose or pointed in odd directions. I designed an LED/coin battery holder to hold both pieces in place and attach to an earring blank. Uses a CR1220 coin battery. ...

Coin cells should fit equally well in all positions now.Fixed issues with bodies not being updated correctly when changing certain user parameters in the Fusion360 file.Fusion360 source file has some user parameters to easily adapt the design to...

Remixed njcrawford's coin cell holder to only hold four cells, as that's all I needed.

This is a remixed version of bmcage that allows one to enter in numbers rather than use sliders when customizing the battery holder for different battery types.

... original/MK2: 1. ...Lip to hold the top on 2. Thicker dividers to make them stronger 3. Slightly more clearance to make coin cells easier to remove Fusion360 source file has some user parameters to easily adapt the design to other coin cell sizes.

... of http://www.thingiverse.com/thing:79259 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=79259 Instructions Using the following options: custom_radius = 10 nr = 20 battery = CR2032 custom_width = 3 sizedivider = 2

... of http://www.thingiverse.com/thing:79259 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=79259 Instructions Using the following options: custom_width = 3 battery = AG13 custom_radius = 6 nr = 11 sizedivider = 0.8

... of http://www.thingiverse.com/thing:79259 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=79259 Instructions Using the following options: battery = CR2032 nr = 10 custom_width = 3 custom_radius = 10 sizedivider = 0.8

... of http://www.thingiverse.com/thing:79259 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=79259 Instructions Using the following options: sizedivider = 0.8 custom_radius = 10 battery = CR2032 custom_width = 3 nr = 10

... of http://www.thingiverse.com/thing:79259 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=79259 Instructions Using the following options: nr = 25 custom_radius = 10 battery = CR2032 sizedivider = 0.8 custom_width = 3