colorfabb filament 3d models
173327 3d models found related to colorfabb filament.
thingiverse
Assembly 3 file is suitable to print on M3D. You will need below parts to assembly ; -Bolt : M8x30 mm (4) -Nut : M8_DIN 934 (4) -Washer : M8_DIN 125 (8) -Bolt : M5x20 mm (8) -Nut : M5_DIN 934 (8) -Bearings : 608ZZ (4) It is just too solid and over...
cults3d
Clip that will slide around the edge of a filament spool as needed and allow filament end to be kept in place when stored. ... Designed for ColorFabb spools, but works on monsterfill too and probably others.
thingiverse
Print three of these spool rims, put the in the hub of a spool from Colorfabb, and it will make it wider, filling up the space so that it fits in a PrintrBot plywood power tower.
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
myminifactory
This is a shaft for the big spool holder of Mark Wheadonhttp://www.thingiverse.com/thing:761893 I designed it to use it with FormFutura filament spools.Update 2016-01-04: I mentioned that it also fits to ColorFabb's filament! The outer diameter is...
thingiverse
Update 2016-01-04: I mentioned that it also fits to ColorFabb's filament! The outer diameter is 52mm. The length is 100mm. (v1 - v3) The length is 115mm. (v4) The large diameter where the spool is placed is about 65mm in length. There are 4...
thingiverse
I customized the filament holder by FaberUnserzeit to fit for Colorfabb Filament Spools (53mm diameter). Update: Printet and tried it. fits very snug into the colorfabb spool. On one side i had to use a bit of force to get it in, since the print...
thingiverse
Using three 3D prints, I have been converting my old clear ColorFabb Filament Spools into planters. These filament spools are roughly 200mm in diameter and 55mm high. I print: 1) One Bottom Piece (usually with a 0.75mm nozzle for faster speed)...
thingiverse
An adapter to allow you to use ColorFabb printing filament in the Makerbot filament case and maintain a smooth movement and flow. ... This is sized for ColorFabb standard spool sizes.
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:915435 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=915435
thingiverse
This clip is designed to fit on the spools used by ColorFabb.
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
youmagine
Use this new version:https://www.youmagine.com/designs/faberdashery-spool-erIt's a design to try to reuse the empty plastic spools from Formfutura or Colorfab.Print x3 for Colorfabb and clip them on the holes it has.Print x4 for Formfutura for the x4...
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
stick thick side to the spool center, thin side to cordless drill and start spooling. ... I'm using this to spool filament out from 2.2kg spool to smaller one since the big one has too much inertia to feed from directly.
prusaprinters
stick thick side to the spool center, thin side to cordless drill and start spooling. I'm using this to spool filament out from 2.2kg spool to smaller one since the big one has too much inertia to feed from directly. Category: 3D Printer Accessories
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
As the filament spools of ColorFabb PLA Economy didn't fit onto my standard spool holder, I modified the Freestanding Filament Holder by voltivo to suite them. Width is 120mm now. Spool diameter is approx. 30cm now. ... Additionally I added screws...
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069