command strip shelf bracket 3d models

... you'd rather print them too. Command strip mounted, so you can use more or less brackets for extra support. I suggest 3lb or 5lb command strips. Each piece should be printed on the side, except the boxes which should be printed upright. ...

... if you'd rather print them too. Command strip mounted, so you can use more or less brackets for extra support. I suggest 3lb or 5lb command strips. ... Each piece should be printed on the side, except the boxes which should be printed upright.

This is a simple shelf that uses Large 3M Command Strips to hang.

... excess glue. On the back of the hook plate, place two long Command Strips directly behind the shelf bracket. Follow all steps of the Command Strips for best results. ...Be sure to test the shelf carefully before placing any valuable items on it.

... excess glue. On the back of the hook plate, place two long Command Strips directly behind the shelf bracket. Follow all steps of the Command Strips for best results. ...Be sure to test the shelf carefully before placing any valuable items on it. 

... on each vertical near the top of each upright. You could put a second one at the bottom to make it sit more upright. I have some very strong hook & loop Command Strips (16lb) and I will often split them or cut them down to fit the space allowed.

... and also changed the orientation so that it prints much faster and has more strength. I use them to hold my Monster High dolls. Instructions You can still use push-pins to adhere it to a wall, but small command strips will probably work better.

This is a 7" x 4" shelf designed to fit on the base of a command strip. It is very rugged considering it is 3D printed, and can hold 15 pounds or more worth of objects if installed correctly. Put this anyhwere you want for damaged free shelving in...

This is a 7" x 4" shelf designed to fit on the base of a command strip. It is very rugged considering it is 3D printed, and can hold 15 pounds or more worth of objects if installed correctly. Put this anyhwere you want for damaged free shelving in...

Brackets to add to your 3D designs to allow mounting with Small and/or Medium 3M Command strips. Has a removable cover so you can get to the command strip pull tab for easy removal. ...Example photos of a small corner shelf I made for my bathroom.

Print 2 of these to hold up a whiteboard. ...Use 2 medium command strips per bracket. ... I use pieces of 1/4 inch weather stripping as standoffs for the bottom of the board so it stays parallel with the wall.

Remiex off the original command strip shelf by ToyMaker2, just made the columns and arches a little wider to fit the bigger command strips, and wider arches so should support more weight.

... a moderately sized printer. Features include; Uses small Command Strips, allows access to Command Strips for easy removal, Print orientations designed for maximum strength, Print requires no support material, Assembly requires no glue or adhesives.

This is a remix of the secret shelf by Tosh, I really liked the design but didn't want to have to make holes in my apartment that I would have to fix later This remix removes the screw holes to provide enough space to attach a 3M command strip (or...

... small things that shine on their own. ...The main goal was to use command strips to mount it, for renters or people who don't want to ruin their wall. ...Another purpose was to organize them in whichever way you like, not limited by a horizontal plane.

The main goal was to use command strips to mount it, for renters or people who don't want to ruin their wall. Another purpose was to organize them in whichever way you like, not limited by a horizontal plane. It's a very easy print - .2mm layer...

Print optimized construction for a simple cell phone shelf that uses size Small Command Strips. NOTE 1: You will need to duplicate and modify the support in order to have both sides. A suggested print orientation file is included in the files...

Roomba Charger Command Strip Bracket This bracket fits on a Roomba charger and is just large enough for 2-3 medium sized 3M command strips to hold it against the wall or baseboard. It's probably a little thicker than it needs to be, but my...

Roomba Charger Command Strip Bracket This bracket fits on a Roomba charger and is just large enough for 2-3 medium sized 3M command strips to hold it against the wall or baseboard. It's probably a little thicker than it needs to be, but my previous...

This bracket is designed to stick to the inside vertical surface, have a shelf sat on top and the tight fitting of the shelf should make it pretty strong as the strip wont be able to peel off. It is designed for the small strips but can of course...

Wanted a shelf at my dorm for 3d prints and other small objects, this uses a command strip adhesive and has a hole/notch for phones so you can charge. Personally I use it for Zoom meetings. There is a hook file included which you can attach to the...

Remixed shelf to add a support rib. ...HUGE difference in strength if you use it regularly to hold objects like phones and bluetooth speakers.

Simple bracket sized for 3M Command Picture Hanging Strips. I've designed the for holding an LED strip under my bed, which had some 3M self-adhesive back side, but didn't hold strongly enough. Due to the nature of the 3M strips I can now also remove...

A quick remix of TheNam3less' "Valve Index Base Mount Corner Bracket" for use with 3M Large Command Strips. (https://www.command.com/3M/en_US/command/products/~/Command-Large-Refill-Strips/?N=5924736+3294529207+3294773680&rt=rud ) to save from...

A bracket to attach a power strip with a cross section of 42mm tall by 39 mm deep horizontally across multiple Closetmaid shelf uprights.

Printed with supports, this bracket allows you to wall-mount an OpenRC F1 car with just a command strip. ...Printed in PETG using variable layer height, although I'm sure pretty much anything will work.</p>

A quick remix of TheNam3less' "Valve Index Base Mount Corner Bracket" on Thingiverse for use with 3M Large Command Strips. (https://www.command.com/3M/en\_US/command/products/~/Command-Large-Refill-Strips/?N=5924736+3294529207+3294773680&amp;rt=rud )...

... Strips (as are most of my designs). My Calphalon griddle is 12mm high at the lip so the spacing for these brackets is 12.5mm + the spacing of the Command Strips. ...I'm sure these brackets could be modified easily for different sized griddles.

Simple Shelf, I used a .8 nozzle on mine. ...Should work fine with a .4!

...... The part can be printed with the command strip portion on the bed, or rotated 90 degrees so the hook is planar to the print bed and well supported. I included the Solidworks file in case the .125" channel doesn't fit the light strip you are using.