command strips for cubicle 3d models
2302764 3d models found related to command strips for cubicle.prusaprinters
This is a hook for 3M Command adhesive strips. If you’re like me you have some extra strips laying around, I have a bag of extra strips.The backing is 75mm x 20mm. ...I used the large strips, the medium strips are the same width but shorter.Print...
pinshape
A remix of http://www.thingiverse.com/thing:50147 with two changes: removal of screw hole; and altering the size of the back of the bracket to accommodate a 3M Command strip (size "small", ~16mm x 30mm) I inadvertently taught myself OpenSCAD to do...
cults3d
altering the size of the back of the bracket to accommodate a 3M Command strip (size "small", ~16mm x 30mm) I inadvertently taught myself OpenSCAD to do this, so I will attempt to make it customizable like the original, and allow for the Command...
thingiverse
A remix of http://www.thingiverse.com/thing:50147 with two changes: removal of screw hole; and altering the size of the back of the bracket to accommodate a 3M Command strip (size "small", ~16mm x 30mm) I inadvertently taught myself OpenSCAD to do...
thingiverse
Needed a fairly deep headphone hanger to accommodate Razer Nari headphones. ... Attached via 3x command strips (probably overkill).
thingiverse
Being inclined to over engineer, I designed it to be able to use command strips and cleats like the commercial hooks you buy. You will need 2 cleats. they may fit a little tight, so you might need to reduce your size buy a couple of percent in the...
thingiverse
A simple Coat hook for 16lbs Velcro Command strips
thingiverse
Suitable for 16mm x 52mm Command Strips / PowerStrips. ... Resizeable in Tinkercad to fit every command strip size: https://www.tinkercad.com/things/4FstgUtbGTj
prusaprinters
Hooks for 3M Command Strips (Medium) that can hold up to 1.3 KG.
thingiverse
For hanging up a curtain rod of max diameter of 3/4" using 3M Command Strips. ...Simple as that.
thingiverse
Remix of Precision Screwdriver Rack by Walpeup. ...This version is for 3M Command strips rather than peg-board.
thingiverse
This is designed for the small 2" command strips. ... It lets you temporarily mount your camera to any flat surface
thingiverse
I remixed the Oculus Touch wall mount designed by randommagic to use command strips to attach to a wall. ...Instead of screw holes I've changed the model to have a solid back plate for 3M command strip attachment.
thingiverse
Not the best, but tweaked to fit large command strips
thingiverse
Cable hook designed for use with the small 3M Command Strips. ... For the greatest strength, I recommend printing on its side with a brim for stability.
thingiverse
... necessary. If there is enough demand, I can easily modify for different command strip thicknesses. ... Onshape Design: https://cad.onshape.com/documents/723fccbea5400147b26feee6/w/dab9264bd3e5bb95e06ff6b8/e/8b3752a5c16d325d981f554d
thingiverse
This cable clip is designed to with the smaller 3M Command Strips. ... For the best strength, I recommend standing the clip on it's side (as pictured), and using a brim for stability.
thingiverse
Remix to make the hat clip apartment friendly, use a command strip.
thingiverse
... frames. Check the packaging of your command strips to determine the right weight for you. Follow the instructions on the Command Strip packaging for how to use them. ...Just stick them to the back of this piece and then stick them to the wall.
thingiverse
I designed this to work best with the large 3M Command strips, the ones that are rated to 5 lbs, however it also works just as well with the medium Command strips, too, for smaller pictures. I've hung many framed pictures throughout the house...
prusaprinters
Modified AmicoJeko's model to thicken the base slightly to fit command velcro strips rather than the standard strips that would leave an exposed pull tab. The velcro ones can be completely invisible.The strips I used are 20mm wide and 50mm long on...
thingiverse
You just apply the Command Strip to the narrower face of the Wall Plate, apply to the wall, and slide the hook over to the plate while keeping the pull tab hidden. I added notches to the Wall Plate to assist with centering and positioning at the...
thingiverse
This was designed with the depth, width, and height of a velcro 3m command strip in mind. Specifically one with a surface area of 75mm x 20mm. ...The ability to remove the headset mount and replace it with a mount meant for controllers or an upgraded...
thingiverse
... command strips. ... 3M says these strips should hold 5lbs, I'm using 2 of these so they should hold 10lbs(?). We'll see how they hold up over time. These are the command strips: https://www.amazon.com/dp/B000FCGS5Y/ref=cm_sw_r_tw_dp_U_x_I-MIEbA5H5SG1
prusaprinters
This wall hook is designed to fit the small 3M Command strips and hide the pull tabs like the official hooks.It uses a two-part mechanism similar to those found on commercial hooks. Apply a small-size Command strip (or any foam adhesive, really) to...
thingiverse
A simple remix of the CPAP wall hanger with plates added to apply 3M Command Strips or some other adhesive to.
thingiverse
This mount is designed to make helmets seem like they're floating on the wall and is secured with command strips.
cults3d
This mount is designed to make helmets seem like they're floating on the wall and is secured with command strips.
thingiverse
I wanted a screw-less blind cleat to use my existing 3M Command strips. ... Starting from evolseven's design, I taught myself FreeCAD and modified the design to suit my needs.
thingiverse
The hook is intended to be fixed to the wall by means of a Medium sized (50mm x 20mm) 3M Command Strip. Where the frame rests on the hook, the hook has been rounded over to allow for easier levelling of the frame once it's on the wall by moving...