command strips for curtain rods 3d models

Hanging up a curtain rod of maximum diameter is a straightforward task when using 3M Command Strips. ...It's that simple.

Not the best, but tweaked to fit large command strips

Designed to use 2 heavy-duty command strips to hang a curtain rod onto the wall without screws/drywall mount. Snaps onto a 23mm (0.91 inches) diameter rod. ...Print without supports/brim/raft with large face down on bed.

This is a hook for 3M Command adhesive strips. If you’re like me you have some extra strips laying around, I have a bag of extra strips.The backing is 75mm x 20mm. ...I used the large strips, the medium strips are the same width but shorter.Print...

... bracket to accommodate a 3M Command strip (size "small", ~16mm x 30mm) in one fell swoop. ...I'm now going to attempt to make it adjustable, like the original, allowing for customizable Command strip tabs - resize to fit bigger/smaller strips and more!

altering the size of the back of the bracket to accommodate a 3M Command strip (size "small", ~16mm x 30mm) I inadvertently taught myself OpenSCAD to do this, so I will attempt to make it customizable like the original, and allow for the Command...

You can find these 10mm x 10mm x 29mm mini bubble levels on Amazon and probably other places too.The two pictures are with it attached to the wall and two XLarge command strips on the back, one picture with the bubble level inserted and one with it...

Needed a fairly deep headphone hanger to accommodate Razer Nari headphones. ... Attached via 3x command strips (probably overkill).

A customized remix of thing:50147 with two key modifications: removal of the screw hole and alteration of the back bracket size to fit a 3M Command strip. The latter change necessitates a small, approximately 16mm x 30mm, size "small" strip. ...This...

Being prone to overcomplicating things, I designed it with command strips and cleats in mind, similar to the commercial hooks you buy. You'll need 2 cleats for this project, which might fit a bit snugly, so consider reducing your print size by 2% in...

I created these command strip curtain rod hooks because I despise making holes in my walls. I aimed to craft a design that would print quickly and look great without drawing excessive attention. This is the result. I use three hooks for a fairly...

... like this curtain holder. ...I designed it because of a problem I had with the curtain support, because when I put the curtains up they bent due to the weight. ...Also consider giving them interior spaces so you can put clamps and secure them better.

A simple Coat hook for 16lbs Velcro Command strips

Suitable for use with 16mm x 52mm Command Strips / PowerStrips. ...Resizable to fit any command strip size in Tinkercad: https://www.tinkercad.com/things/4FstgUtbGTj

Hooks for 3M Command Strips (Medium) that can hold up to 1.3 KG.

A DIY innovation that reimagines the humble CPAP wall hanger by integrating removable adhesive strips, namely 3M Command Strips or similar products, for effortless installation and removal.

Cable hook designed for use with the small 3M Command Strips. ... For the greatest strength, I recommend printing on its side with a brim for stability.

... necessary. If there is enough demand, I can easily modify for different command strip thicknesses. ... Onshape Design: https://cad.onshape.com/documents/723fccbea5400147b26feee6/w/dab9264bd3e5bb95e06ff6b8/e/8b3752a5c16d325d981f554d

Remix to make the hat clip apartment friendly, use a command strip.

This cable clip is designed to with the smaller 3M Command Strips. ... For the best strength, I recommend standing the clip on it's side (as pictured), and using a brim for stability.

This innovative solution was created specifically for compact 2-inch command strips, allowing users to effortlessly attach their cameras to any level surface for a short period of time.

... frames. Check the packaging of your command strips to determine the right weight for you. Follow the instructions on the Command Strip packaging for how to use them. ...Just stick them to the back of this piece and then stick them to the wall.

Modified AmicoJeko's model to thicken the base slightly to fit command velcro strips rather than the standard strips that would leave an exposed pull tab. The velcro ones can be completely invisible.The strips I used are 20mm wide and 50mm long on...

I designed this to work best with the large 3M Command strips, the ones that are rated to 5 lbs, however it also works just as well with the medium Command strips, too, for smaller pictures. I've hung many framed pictures throughout the house...

You just apply the Command Strip to the narrower face of the Wall Plate, apply to the wall, and slide the hook over to the plate while keeping the pull tab hidden. I added notches to the Wall Plate to assist with centering and positioning at the...

... ...Attaches with a standard 3M Command Strip, and there is a small slot for lining it up. I made it to hold my Logitech G933 headset, but should work with others. ...Printed with Inland PLA+, on its side, 25% gyroid infill, no supports or brim needed.

This was designed with the depth, width, and height of a velcro 3m command strip in mind. Specifically one with a surface area of 75mm x 20mm. ...The ability to remove the headset mount and replace it with a mount meant for controllers or an upgraded...

Apply a small-size Command strip (or any foam adhesive, really) to the back of the anchor oriented with the opening up, press the anchor to the wall, and slide the hook on top.Should be printed without supports. ...Use more infill for greater strength...

This wall hook is designed to fit the small 3M Command strips and hide the pull tabs like the official hooks.It uses a two-part mechanism similar to those found on commercial hooks. Apply a small-size Command strip (or any foam adhesive, really) to...

This mount is designed to make helmets seem like they're floating on the wall and is secured with command strips.