computer fan mods 3d models

The first mod was a simple one - I replaced the stock propellers with slightly larger ones. This gives my cub more thrust and makes it easier to handle. Next, I added a lightweight battery compartment. This lets me carry more power without adding...

Mods: Widened Top Plates (40mm). Enlarged Main Compartment to Fit NAZE32 Standard Flight Controller. Enlarged Rear Arms to Fit Turnigy Lipo (+1cm Larger Battery Compartment). Consolidated Carbon Frame Bottom Plate (3mm, 1.6mm Genuine). Spektrum...

I used foam mounting tape (super glued the tape to the mod, but just the tape to the ramp, so it's reversible). You'll need to recalibrate your projector for the billboard after installing. The bulb cones are NOT plug and play. I...

I modify and upload different versions of my Proxxon MF70 CNC conversion.\r\n\r\nCurrently available:\r\n+ An upper plate mod that supports only one 626 bearing, ideal for high-quality deep groove bearings with ABEC3* or higher precision.\r\n+ A...

... is also my creation. The feet are thing:129448 with rubber added to prevent slipping. Printing was done at .2 mm layer height; the filament guide and fan bracket required support materials, while the coupling was printed hollow with 3 perimeters.

This contains 2 modified lids for using 30mm and 40mm fans.One also has a cutout for unlimited height capacitors if the original does not fit.

... ...These mods for your printer are for the front faceplate and for the z-axis. Simply print and place on. It will cover up the Ender 3 Facebook QR Code. You may need to tweak the front cover plate to make it shorter or longer depending on your print.

Mods for this awesome model, a single print parasol, and a layered body so you can layer change to get colours. Not exactly plug and play, you will need some pieces from the origin models or make your own and you will need to modify the main...

This will be a collection of mods created for the ROKR Pinball puzzle. The puzzle is a kit that when put together is a playable pinball machine. Base - This is a frame that fits in the bottom cavity of the machine. When attached to a piece of wood...

Components: * TL250H Quadcopter Frame * ESCs: LittleBee Spring 20A ESC BLHeli_S 2-4S Favourite FVT * Motors: MULTISTAR V-SPEC 1808 - 2400KV * Props: Dalprop "Cyclone" T5045C 3-Blade * BEC: 5v * Flight Controller: NAZE32 Acro Betaflight firmware *...

List: - Feet - XT60/Switch Mount: Includes connector, M3 screws/nuts, thick wires, optional switch, soldering iron, drill, for easy installation - Fan Adapter with Optional LED Mount: Features adapter for 30-40 fans and includes mount for T10 LED...

... Motors. Replacing the Print Bed MOSFET for Enhanced Performance and Reliability. Adding Four Powerful 24-Volt Fans for Improved Airflow and Cooling Efficiency. Designing a Custom Fan Power Distribution Board to Ensure Seamless Power Management.

I removed the outer shell of the blaster because I prefer the simple, smaller blaster that it is on the inside, and some of these mod parts are only able to be attached after removing the outer shell. The ST adapter is a friction fit adapter that...

... and buffer full. (had to use 5-pin automotive relay instead of 4-pin Remixed from: https://www.thingiverse.com/thing:4257637 https://www.thingiverse.com/thing:4145271 Tom-Penns collator mods (no longer on thingiverse) Photos are coming soon... ...:)

... At the top, a convenient 1-inch or 25.4 mm segment allows users to grasp wrenches securely as they screw the mod into place on the lab faucets. Print Settings Rafts: Yes Supports: Yes Resolution: A precise infill layer resolution of 0.1 mm.

I'm not responsible for any damage that might occour in combination with these mods!** My own designs: * simple rear wing/spoiler - should be printed in TPU! * front shock protector/brace - M3x25 screws needed - the stock screws will fit, but...

A couple holders for 40mm case fans and a spot for the wrench they give you.I printed in PLA and found no warping but your results may vary. I wanted to mount a few 40mm fans in spots around the case to play with cooling.  I didn't notice any...

... need to be drilled to fit M3 grub screws) 5: drive shaft couplings for no binding I am using the gears modified by:Eight20 @ https://www.thingiverse.com/thing:1937515 Printed at 100% infill. More mods to come as testing is still in the process

Here is the start of my BLV Cube mods. I will be slowly adding additional remixes of the original parts. Parts: * Z motor mount These motor mounts have room for using Rubber O-rings. For those who wish to use solid couplers or integrated lead...

This front sight piece mod and bolts(arrows) fly straight and the thicker design of the front piece increases the power of your crossbow slightly. For use with the cheap toothpick crossbows that you can find on Wish, etc. The new front sight...

Here is the shopping cart for all my mods: - [Banggood Z-Axis Fixture](https://www.banggood.com/de/Aluminum-Z-axis-Lead-Screw-Z-Rod-Bearing-Holder-with-Bearing-Housing-for-Creality-3D-CR-10-Enedr-3Pro-3D-Printer-p-1577566.html?rmmds=myorder) -...

Source files can be found on GitHub at [https://github.com/brandonhill/Eachine-Racer-130-mods](https://github.com/brandonhill/Eachine-Racer-130-mods). I made this modification because I initially had a problem with the stock flight controller, so I...

Mount your fan on a sturdy Z-axis mount to keep it firmly in place while you work with precision and control. ...A robust Z-axis plate provides stability and ensures smooth operation of your equipment, giving you peace of mind as you focus on the task...

Adjustments made include: 1) Installation of a tube for a 12V LED light, wired in parallel to the fan. 2) Extension of the bracket for bottom screws. 3) Addition of a bumper for the x-axis switch. 4) Pillars added to enhance connection with the...

remix to use biger fan

Files: - large spacer: to be glued to the receiver - small spacer: can be used to space the spacer in the arm - mod bullet: the bullet that fits the cylinder If you enjoy my prints or remixes please consider becoming a Patron! Early STLs, images of...

Revise PrintrBot Simple V2 components with 3dtin.com designs at 0.7 scale; flanged cap revisions for spool compatibility, right-angle fan brackets, 30.5mm flanged caps fitting standard PLA spools, reamed 8mm foot/elbows for smooth rod usage, and...

All of my mods for my mpcnc primo F-25mm. STLs are oriented for printing. Everything prints without supports, except a few parts. Please refer to the description below and/or the included gcode. XY EndstopsHardware needed:2x M3x5x6 heatset insert, or...

WL Toys V950 helicopter mods as per YT video - https://www.youtube.com/watch?v=jDN8mQqpB10 NB. All these will need fettling. I've had these on three V950s and they've all been slightly different. 1. Brace across chassis mounts. Pretty easy. 2. ...

I also redesigned the back plate to allow attaching wrist rests and have included the current ones I'm using.  In the pictures you can see the fully modded Sofle, I cut the new backplate out of  frosted 5mm acrylic as I think it looks nicer then the...