concept 2 rower ipad holder 3d models
1240274 3d models found related to concept 2 rower ipad holder.thingiverse
This thing slips right onto a concept 2 PM3 and provides a post to mount a bicycle style phone holder. ...Could easily be modified to have its own holder.
thingiverse
Phone holder for a concept 2 rower. ... All .stl files with "1X": Print one of each stl in PLA or PETG .stl file with "2X": Print two in TPU .stl file with "4X": Print four in TPU Use a rubber band as shown in picture.
thingiverse
... This remix also uses a honeycomb pattern rather than the original slats (as they proved impossible to print for me). I also had an accessory from Concept that I modeled as the slip on holder that screws to the underside of the iPad holder.
thingiverse
Tablet support for Concept2 Rower works with - elastic rope blocked by 2 knots (about 2.5 or 2.7 diameter) - 2x TCHC M3x16 - 1x TCHC M3x12 - 3 nuts
thingiverse
Used to hold 10" ipad mount slides onto the PM5 support bar Top section uses: M3x30 socket cap flat head screw (3TSSFM03x30) x1 3x0.5 low square nut (FC-35622410) x2
thingiverse
iPad Mini Holder for Concept-2 indoor rowing trainer. It's intended to use iPad-Mini with cover. Just flip the cover over the mount panel. ... I sticked a thin rubber tape on the socket to prevent iPad to slip.
thingiverse
An iPad holder on top of [concept 2 smartphone cradle](https://www.concept2.com/bikeerg/accessories/smartphone-cradle) with simple design(minimum support + no assembly required) Coming in 3 different flavors.
thingiverse
Adjustable Mobile Phone Mount for your Concept 2 Rowing Machine. Works for devices with a width of up to 100mm. To get a secure fit, attach a rubber band between the two parts. ... Enjoy!
thingiverse
This is a two peace print, designed for the Concept 2 Rowing Machine, which holds your ipad, or smart phone (does depend on the size of the phone). I have included .skp files for anyone who would like to edit. ... Enjoy!
thingiverse
... controller flashes the LEDs and rechargeable AA-batteries keep the device going. They last until you look like a Body Builder, (ha-ha-ha). The holder is put over the PM5, the Thing is put into the holder. That’s it! Enjoy your workout! ...
thingiverse
Holds and Ipad 8 on concept2 rower. Slip fit in PM base. Remix of "rvandepo"s ipad mount. added chamfer to slip fit edges for easier fit and resized for ipad 8. Please see his images to view mount location if needed. ... Print as shown in photo not...
thingiverse
... the arm). To install, put the lower (1-piece) clip on the arm up high, just below the PM3/4/5, then slide it down until tight. Next rest your iPad in the lower clip, then align the upper clips to top of iPad and press them into place in the arm
thingiverse
Wanted something that would hold my Phone running the Concept 2 ERG Data app and a Ipad playing a video. Unit slides on and off very easily. Top phone holder mount can be removed. Bolted a quadlock on first then redesigned it so it could be...
thingiverse
I designed this object to guide and maintain the heart rate sensor cable against the rail.
thingiverse
Just my laymens approach to a phone holder for the waterrower. Best fits phone around 76 mm in width. ...Inspired by https://www.thingiverse.com/thing:4182183
thingiverse
I printed out the [Tablet holder with 4 tension claws](https://www.thingiverse.com/thing:3283103), but placing and removing the tablet is uncomfortable with 4 moving arms. This design is a full redesign that fits the same screw holes as the design...
thingiverse
I needed a holder for my iPad Mini 2 to attach to a flat surface, so I made this remix. I removed the handle and flatted the back. ... I've added a v3 with m3-sized holes so you can screw it to something
prusaprinters
Tablet Holder iPad Air 2 serving for mounting in VESA 100 mm x 100 mm TV bracket.Material: PLA (PETG).Supports: Yes.Layer height: 0,2 mm.Connecting material: Concussion head screws 6 mm.NOTE: The thread of the top tablet fuse must be plainted with a...
prusaprinters
I needed a holder for my iPad Mini 2 to attach to a flat surface, so I made this remix. ...I removed the handle and flatted the back.</p> <p>I've added a v3 with m3-sized holes so you can screw it to something</p> <h3>Print Settings</h3>...
cults3d
It's a phone holder for anything with a Concept 2 PM monitor. It uses a rubber band on the back to clamp down on the phone. ... Enjoy
thingiverse
It's a phone holder for anything with a Concept 2 PM monitor. It uses a rubber band on the back to clamp down on the phone. ... Enjoy
thingiverse
IPAD 2 LCD screen holder. i split the file because it had to fit my ender 3. but i glued my together and it works great. ... this case is just for the actual LCD without some form of glass in front of the LCD.
thingiverse
... the two parts together. Although its a tight fit, I’ve also used a bit of hardware ( nuts/bolts/washers) to secure things Hardware iPad holder to stand 1/4” 20TPI 1” long hex head bolt Washer & nut Base plate to stand M6 X40 bolt Washer and Nut
thingiverse
... are small but hold the ipad very good. Print them <b>standing on the side</b> to avoid breaking of the hook due too layer splitting. In the end i printed 4 long holders so i can easy get the ipad horizontal. ... Any comments are always welcome.