connector cap 3d models
130923 3d models found related to connector cap.thingiverse
Wired remote controller connector cap for Warn VR. ... I don't know why this is not included with the winch ...
thingiverse
Derived from http://www.thingiverse.com/thing:661360. ... I needed two Type N connector caps at the same time. ...Easy fix since they're the same exact size.
thingiverse
... caps. ... Has a groove for an oring and fits down inside the connector cap, which then screws onto the female end of a pigtail/extension cable DISCLAIMER: These have not been tested for waterproofing and should not be considered as water tight.
thingiverse
3S Balance Connector Cap UPDATE: The initial measurements were take from Tattu batteries for which the caps fit very well, however they do not fit Turnigy nano-techs very well. ...Print Settings Printer Brand: RepRap ...
thingiverse
I quickly designed this banana connector cap. Helps to prevent short circuits when loose ends may connect unintentionally. With the cap the contacts are protected. Insert banana connectors while still warm for best fit. Print Settings Printer: ...
thingiverse
I needed some connector caps for my patch panel in the winter. The barrel connectors get cold, and they get covered in condensation. This fixes the problem. Instructions I measured the connector, made a cylinder with a couple cuts, and a cone to...
thingiverse
Connector cap for Ryobi One+ batteries (18V). The 2 parts should be printed without support as laid out in the STL files. OpenScad source provided. ... The source includes 2 versions: -one with battery clips, banana sockets and a power switch ...
thingiverse
This new XT-30 connector cap design features a finger grab section on top for ease of installation and removal, and the never seen before retention loop on the side of the cap. Use this loop to store your battery's cap on an open switch of your...
thingiverse
This new xt-60 connector cap design features a finger grab section on top for ease of installation and removal, and the never seen before retention loop on the side of the cap. Use this loop to store your battery's cap on an open switch of your...
cults3d
Needed an SAE Connector Cap, and decided to Remix the one from Axelisart (https://www.thingiverse.com/thing:4057314) to emulate the one that came with my battery tender that had a built-in leash. ... I printed this with TPU.
thingiverse
Needed an SAE Connector Cap, and decided to Remix the one from Axelisart (https://www.thingiverse.com/thing:4057314) to emulate the one that came with my battery tender that had a built-in leash. I printed this with TPU. ...
thingiverse
Cap for an aviation connector. Step file included. ... 0.2mm layer height.
thingiverse
simple cap for idc connector, specially for eurorack busboards to prevent dust or any objet in your power lines.
thingiverse
Original design of protective cap for my e-bike's power cable (standard XT60 connectors used). ...Print Settings Printer: Faberant Rafts: ...
thingiverse
Just a cap for the XT60 battery connector found on LiPo batteries for Quadcopters and planes. ...Print Settings Printer Brand: Printrbot ...
thingiverse
This is a cap for female xt90 (-s) connectors. With a hole for a string, lanyard or whatever. ... Fits perfect with my printer, but you might have to scale it to get a good fit.
thingiverse
... end. ... This is a simple knurled cap for the female end of the connector when not in use. ... Used on waterproof LED wire connector: https://www.amazon.com/gp/product/B07WDBLFDN/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=UTF8&psc=1 Printed at 100% infill
thingiverse
Removed my navi preparation from my 2022 S1000XR and could not find the part code for the blank cap that you plug into the connector, so I built this. It should work on other models too. ... Printed with PETG, 0.2 layer height with supports Print...
thingiverse
Mainly used as a replacement for a missing cap on the GX16 connector on my electric scooter. ... You can trim the end if you want a shorter version, or swap filament before the end of the filet with TPU to make it more water-tight.
thingiverse
After I had made the cap, I noticed that the connector was still a little loose in the plastic housing, probably from riding around in my pocket all the time. So I made another version that covers the whole thumb drive all the way up to where the old...
thingiverse
This is a cap designed to fit over the XT60 connector. I usually keep all my Lipo batteries together in a box and it has always been in the back of my head that one fateful day two batteries will short themselves together. Hence, a simple cap. I've...
thingiverse
This is dust cover for numerous RF devices with SMA connectors. Inner hole made "conical", you can adjust length and diameters of cone to suit your printer. ... Mine works fine for Prusa MK3 and most of SMA connectors.
thingiverse
A quick 4mm hose connector adapter. ...This was modeled using the dimensions from [Pipe / Tube / Hose Connector](https://www.thingiverse.com/thing:1324986). ... You can use any material you want, but I went for TPU to ensure a good seal.
thingiverse
Inside Thingiverse I could not find an XT30 cover that fit my connectors precisely, or they were too tight or too loose, so I decided to design an XT30 cover myself.
myminifactory
Flexible endcap for XT90 FEMALE connector. Printed in Priline TPU but any TPE/TPU should work. ...Depending on the printer it can be scaled up or down 1-3% to fit better.