connector db9 3d models
60316 3d models found related to connector db9.grabcad
The D-subminiature or D-sub is a common type of electrical connector. ...They are named for their characteristic D-shaped metal shield. When they were introduced, D-subs were among the smallest connectors used on computer systems
grabcad
Based on my metal DB9 male part of connector and added Silvio G. ...Mendonça "Capa plastica connector DB9" (thank you Silvio!).
thingiverse
Set of DB9 connector to mount on a nema17 step motor (HANPOSE-17HS8401-S). ...Made to fit a cat5e cable and hold in place with a zip tie.
thingiverse
In order to build your connector converter you also need the following parts: two DB9 simple connectors (as in the photos); Depending on what kind of converter you need, you can use male-male, female-female or male-female DB9 connectors. internal...
thingiverse
... the joystick's cord. I used the following hardware to build the stick: M3 x 12 flat head machine screws (to replace the ones that came with the joystick) \#4-40 machine screws and nuts (to retain the DB9 connector) DB9 female solder-type connector
thingiverse
Simple DB9 connector mock-up. I needed this to test fit into other things I am making. I see no other use than that. ...Enjoy!
pinshape
... shell for mounting on a DIN rail. ... Printed in ABS at 0.2mm layer height, 20% infill, with supports mainly for DIN rail mounting section on bottom. M3 screws or similar screw straight into plastic to hold DB9 connector - no need to tap holes.
thingiverse
DB9 Face. ...The Db9 Break out board is held on by its own screws. ...No supports
cults3d
DB9 Face. ...The Db9 Break out board is held on by its own screws. ...No supports
thingiverse
This is a Remix of an DB9 connector from: https://www.printables.com/de/@Ouwekaas https://www.printables.com/de/model/409740-db9-housing-at-a-90-degree-angle The cable goes in a 90 degree angle out of the side of the housing. ... Parts needet: 2X...
thingiverse
Update: New pictures were added to include the AB Electronics DB9 (DSUB) RS232 converter. It is also a higher case to add the RTC clocks they provide to stack above the RS232 board. I will add the MOSHI Soft drawing and PDF soon for the new case. ...
thingiverse
... ... Because it is drawn with official measurements. Just substract the plate from your object and the connector is integrated in your design. The cut is also intend to be cut of from your object. ...So you will get a hole in the right size.
cults3d
For troubleshooting serial connections and serial devices i create a loopback tool from a null modem mini adaptor (9 pins) open up the adaptor bij drilling out the holes on the side. connect pin 2 and 3 close the mini adaptor with use of this...
thingiverse
For troubleshooting serial connections and serial devices i create a loopback tool from a null modem mini adaptor (9 pins) open up the adaptor bij drilling out the holes on the side. connect pin 2 and 3 close the mini adaptor with use of...
thingiverse
... into the bottom piece. ...I made this as an experiment to build into a case with DB9 connectors without the use of screws. There isn't much practical use in this by itself. ... Supports may not be needed since all overhangs don't extend very far out.
cgtrader
CAD 3D model for the DB9 female connector through hole
cgtrader
CAD 3D model for the DB9 male connector through hole.
thingiverse
Los Modelos son un Panel Fronta y el Conector DB9M, en formato STL, con sus medidas estandar para ser utilizado en diseño 3D de Cajas de equipos electrónicos. Fueron diseñados en FreeCAD 0.18 Se ha fabricado en PLA, que es un material...