cool easy things to 3d print
4263934 3d models found related to cool easy things to 3d print.thingiverse
This is a small and simple ash-tray. ... With 0.2 resolution, it takes ~1 hour to print. No supports needed. 60mm/sec. ...
cults3d
Cross 3d efect very easy to print. This is a very easy to print cross I have made 2 of them one with a base and one with out a base. The one with a base can stand on its own like on a table or shelf. Both look real good hanging on a wall and the one...
thingiverse
The wall thickness is 1,6mm, so it´s easy to print with a 0,4 or 0,8mm nozzle. I added a little bit more material in the top corners for better stability. In my case, it is water proof. If you have problems with leaking water, you can try to...
cults3d
Here is a easy to Print Lighthouse. ...You don´t need any support for this print.
thingiverse
Here is a easy to Print Lighthouse. ...You don´t need any support for this print.
thingiverse
Remixed to zbrush to facilitate easy fdm printing with no supports needed
thingiverse
An easy to print duck! No support needed! ... You can print it very small and hide in some funny spot!
thingiverse
There are other cool designs online but I always had problems to print them with TPU. This version is easy to print and has the same weight (around 160g) as a freestyle frisbee. You can buy me a coffee if you like the design :) -> #paypal.me/rubbl...
thingiverse
... fdm 3d printer. ... Super easy to print Printing: I used standard cura settings, with 20% infill and 0.12mm layer thickness. the print is about 10cm tall. the holes in the checks are meant for a 3mm fishing line to be glued to for the whiskers. ...
thingiverse
I sliced jeplans' pedestal to make it easy to print with wide ends both on top and bottom
thingiverse
Easy to print hook. ...I use it to hang the helmet but you can use it for anything
prusaprinters
Easy to print handle with one layer closed screw holes for easy bridging. The handle should be printed with the holes on top, flat side down to the bed. ...The holes are made for 5mm screws and can be freed from the helper-layer by piercing through...
thingiverse
A Centripro mount for GoPro. ...I have removed two wings for easy printing. Not tested ! ...Here is a version with all wings http://www.thingiverse.com/thing:1433790 Look at http://www.centriphone.me/
thingiverse
... into you own hands that stuff will be on the kitchen counter until it's time to put the decorations away. Get that junk off your counter with this easy to print hook! This is made to be easy to print and work with the command adhesive strips.
thingiverse
This an easy to print version of Mimikyu, this one can be printed without any supports. ... Several changes where made to the original model: - Re-attach the tail to the body - Slightly tilt the head - Slightly tilt the ears - Arrange the base to make...
thingiverse
A spring specialy designed for 3D printing, easier to print and stronger than casual springs. ... Material : PLA but the spring can be less effective with some use.
thingiverse
This is a Birdhouse made out of 2 Parts so that it can be printed very easy. ... Instructions Print the top and bottem and your done!
thingiverse
Easy to print waterpump. It took me about two hours to print. It pumps about 7L/min with the motor I use (36V 10W from a broken hair dryer). Motor Shaft 2mm Motor mounting screws M2x5mm (the ones from the hair dryer) Casing screews 2,8x20...
thingiverse
Easy to print glasses come in 2 sections, and use a 4mm wide screw to fasten the two halves together. ...The metal parts can be taken from either of the two links below-...
myminifactory
... I've included the easy to print model and I've also included the full model in case anyone wants that as well. Have fun printing! ... Print Settings:Printer: DaVinci 1.0 ProFilament: Hatchbox PLALayer Height: 0.1mmInfill: 20%Supports: NoRaft: No
youmagine
I've included the easy to print model and I've also included the full model in case anyone wants that as well. Have fun printing! ... Print Settings: Printer: DaVinci 1.0 Pro Filament: Hatchbox PLA Layer Height: 0.1mm Infill: 20% Supports: No Raft: No
pinshape
I've included the easy to print model and I've also included the full model in case anyone wants that as well. Have fun printing! ... Print Settings: Printer: DaVinci 1.0 Pro Filament: Hatchbox PLA Layer Height: 0.1mm Infill: 20% Supports: No Raft: No
thingiverse
...I've included the easy to print model and I've also included the full model in case anyone wants that as well. Have fun printing! ...Print Settings: Printer: DaVinci 1.0 Pro Filament: Hatchbox PLA Layer Height: 0.1mm Infill: 20% Supports: No Raft: No