coral frag rack 3d models
30533 3d models found related to coral frag rack.
thingiverse
Coral frag rack and magnet holder. Holds up to 21 frags, you can superglue your magnets in after printing. The holder actually works better if you use it with the printed side facing the aquarium (magnets closest to you). The holes in the middle...
thingiverse
This is a mini Frag Rack, optimized for a Red Sea Reefer. It holds up to 5 small coral frags. ...Optimal for zoanthus and small corals
thingiverse
Simple frag rack that holds 7 frag plugs. ... 50mm tall, prints very quickly, ideal for using to acclimatise coral frags while on your sand bed.
thingiverse
A basic frag rack for coral frags in a reef aquarium. 4x 12mm holes for the frag plugs. 2x 6mm holes for the suction cups. ... Some cheap 20mm suction cups from ebay were a perfect fit.
thingiverse
... Holes are 10mm, which is a good fit for most of the plugs I have found. I'm using the Oceans Wonders coral frag plugs in the picture: https://www.amazon.com/gp/product/B06Y6DYQXW See also my other frag rack: https://www.thingiverse.com/thing:2672511
thingiverse
... are 10mm, which is a good fit for most of the plugs I have found. I'm using the Oceans Wonders coral frag plugs in the picture: https://www.amazon.com/gp/product/B06Y6DYQXW See also my corner-frag rack: https://www.thingiverse.com/thing:2672482
thingiverse
I just wanted a small rack for my corals that wouldn't take up too much space in my tank. It has places for 5 little magnets from a Magnetix toy in the back which should be sufficient. I haven't tested it yet, so I'm not sure if there will be a...
thingiverse
Simple frag rack designed to use home depot magnets. The plugs should be printed solid (100% infill). I used the xenia plugs with a small shell on top. ...
thingiverse
These legs snap in at the holes of a eggcrate plate to lift the racks in your frag tank from the ground.
thingiverse
This is a frag rack that I designed to hold up to 10 3/4" frag plugs. I printed in PETG. It is designed to work with the suction cups shown in the photo. ... They are available from HomeDepot for around 2$ a pack.
thingiverse
Feet are 1/2" in Diameter by 1-1/4" tall, and hold the frag rack (Egg Crate) 1 inch above the bottom of your bare-bottom reef tank or frag tank. Print with 100% fill so the feet aren't too buoyant. Since it is tall with a small base, print...
thingiverse
I also create a coral propagation basket and coral propagation plug holder if you need. All parts were printed at 100% infill using .2 layer height. To keep the holder from moving, I created everything with tight tolerances so depending on your...
thingiverse
Reef Coral Magnetic Frag Rack Rock 4pcs Magnetic frag rack that resembles a rock and fits upto 4 frags. printer for 12.7mm magnets from Dollarama. printed with 10-20% infill and drill holes to balance the load with air and water on the magnets. ... ...
thingiverse
This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/gGe1njX4F9n
thingiverse
Remixed design to support 15 frags and extended the hangars to sit lower in the tank, uses minimal filament. Print 2 hangars. Print @ 100% for 1 inch frags, or 125% for 1.25 inch frags. If scaling up remember to print the hangars at the same % to...
thingiverse
3 Coral frags Racks for reef Aquariums for 4 and 5 plots. ...Fixed or customizable height
cults3d
3 Coral frags Racks for reef Aquariums for 4 and 5 plots. ...Fixed or customizable height
cults3d
This isolator allows to separate a cutting or a coral from the others for its rarity, to avoid that it is burned, to follow its isolated development, to let it resume after a burn.... Hook on overflow or 12 mm glass. ... dimensions of the piece:...
cults3d
Coral rack requiring little stirring to optimize the attachment of these like zoanthus. rainiures allow the passage of a gentle current. Locations of the cuttings posts in the form of rails. The diameter of the studs that can be arranged are...
thingiverse
Simple Frag rack with slot for magnet. Option for 5 frags and 9 frags ( 5 inches and 10 inches long ) Magnet used: Epoxy Coated Neodymium Disc Magnets for aquarium (Diameter approx. ...1" x 3/8" )
thingiverse
You can specify: * number of rows * number of frag plugs in each row * frag plug diameter * frag plug spacing * whether you want to use magnets or suction cups * keyhole or single hole diameters (for suction cups) * magnet diameter (for magnets) *...
thingiverse
A fully 3d printable modular frag rack by Eel River Coral. Legs can be stacked to adjust height and flats fit together for an infinitely expandable design. ...I recommend printing in a reef safe plastic like ABS or PETG.
thingiverse
... through them and fish can explore inside. AND you can drill holes through the top to make them into frag racks if you want to keep your corals on the plugs.... I plan to just glue my corals directly to them. ... Wash thoroughly after printing
thingiverse
Customized version of https://www.thingiverse.com/thing:5991356 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5991356
thingiverse
Customized version of https://www.thingiverse.com/thing:5991356 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5991356
thingiverse
This is a simple coral frag rack that doesn't need magnets. The file provides a holder and the rack (available 2 sizes each). You need to print: 2 x holder 1 x rack You can glue them if you want. ... The hole has a diamater of 18mm.