cord holder for desk 3d models
2368628 3d models found related to cord holder for desk.thingiverse
As a school project i was to design a tool to help people, so here is a nice little hook with screw holes :)
thingiverse
USB cord holder for desk leg that is diameter 40mm(guess it would work on a bit smaller and bigger).
thingiverse
Desk cord holder for 2 and 5 cords. Can be used as a tool holder for example screwdrivers. ... It is design for desk board 16 mm or 5/8 in.
thingiverse
... ...You can clip this Desk Cord Holder onto the side of your desk. The design is specifically for 16mm desks, but do to the flexibility of the design it should work for ±0.3mm. ...Try scaling the design up or down if that does not meet your needs.
cults3d
... being used. The ring diameters are custom for my cords (ethernet, vga, and audio) but they may work for you or you may be able to adjust the diameters to suit your cables. ... It's attached with two wood screws through the cylindrical standoffs.
thingiverse
The ring diameters are custom for my cords (ethernet, vga, and audio) but they may work for you or you may be able to adjust the diameters to suit your cables. It's attached with two wood screws through the cylindrical standoffs. ... ...
thingiverse
This holds your cords up behind your desk to access them easily. ...It uses a 3M Command strip to attach to the side or your desk or wherever else you want to put it.
myminifactory
With my computer under my glass desk, my USB cords are always dangling down and getting run over by the chair (damage in pictures as proof). I finally did something about it. I made this. This is designed for use on a 3/8" (1.1 cm) diameter bar. If...
grabcad
Made for cords to run through a table, organized. ...Was originally made for my teacher, because people stole the covers in the hole for the table...they stole these too...
thingiverse
Just a derivative for one more cord. ... Instructions Print and install under the edge of your desk.
thingiverse
Simple 2 cord holder meant to clamp onto the free edge of an ikea desk. I designed it to fit my printer USB 2.0 cable, but it seems to fit nicely with other similarity sized cables. I designed this as a simple holder that makes it easy to grab the...
thingiverse
This is a EU extension cord mount for 28mm desks (like the IKEA Idasen). No need for screws or glue. If needed, I can provide the design for different desk-widths. ...Just write a comment
prusaprinters
This is a EU extension cord mount for 28mm desks (like the IKEA Idasen). No need for screws or glue. If needed, I can provide the design for different desk-widths. ...Just write a comment</p> <h3> Print Settings</h3> <p><strong>Printer...
thingiverse
Designed some clamps to fit on joist for holding wires. ...The wont hold a lot of weight but they will work for a few wires especially in a temporary situation like mine is.
myminifactory
It wont hold a lot of weight but the will work for a fiew wires. I used it to temporarily get some ethernet cables up and out of the way. Recomend sanding the inside edges with some rough grit sand paper so it will grip better. One file has a 4mm...
thingiverse
I printed this to keep the cords from falling off my desk between the wall. ... The magnetic piece doesn't allow the cord to fall through.
thingiverse
might be useful to others as well - I did not like the cords hanging down underneath my desk. Picture is taken from under the table ... ...have fun and happy printing
thingiverse
I made this after buying a monoprice 3.5mm aux cord extender from amazon because my current aux cord isnt long enough. I figured it would look clean if I mounted it under my desk, so here it is. I know that the holes aren't centered, this is one of...
thingiverse
quick and easy prints to organize cords under this desk I purchased from amazon ( SHW Home Office 55"x60" Large L Shaped Corner Desk )
thingiverse
Needed a Cable holder for my desk so I made this little thing. Very simple and fast to print (0.1mm resolution took about 30 min each). It fits all of my cables right off the printer. Let me know how you like it if you print them :) **Update:** I...
prusaprinters
Desk cord keeper to keep cords on top of desk and organized when not in use. ...4 cord and 6 cord versions both available.
thingiverse
This is a cord holder that I made to hold my computer cord and cell phone cord. I couldn't get any other ones that I printed to work for me. ...I made it to fit up to 4mm cord and with that size it is a tight fit which was what I was going for.
thingiverse
(Thingiverse 4352817 ) There are a few designs for Cord stops on Thingiverse but I did not find one that used a spring to keep things in place. There are lots of these on the internet for sale but they are a bit pricey, especially if you need more...
grabcad
With many new pieces of technology being introduced every day into the office work space, cord management for many different devices is greatly needed. Often times the average office worker struggles to maintain an organized work space. A...