corne keyboard case by 3d models

These legs are designed to be used with almost any case for the Corne keyboard, and utilize the original standoff screws to attach them to the bottom of the case. There are 10mm dia. depressions on the foot of each leg to accommodate a 3/8" or 10mm...

Switch plates for the Corne (CRKBD) keyboard. This one: https://github.com/foostan/crkbd Only 1.2mm thick (Alps specs) so be careful getting them off the bed. However, the switches snap in nicely. They do bend a bit so you might need to sort...

"Ramicorne" keyboard hi-pro case. For 5x3 crkbd. ...Insets for m5 nuts in AMPS pattern to connect to commonly available mounting systems such as Ram Mounts

A case to use your favorite low profile [corne](https://github.com/foostan/crkbd) keyboard on the go. It fits on top of a standard pitch keyboard and is kept in place by little rails at the bottom (YMMV I have only tested this with a MacBook). When...

Liked the design of s-show : https://www.thingiverse.com/thing:4086050 I took the liberty to resize the height and add spacers that can be directly screwed with a M2. Not sure if it’s going to resist a lot of screwing, but on my prototype it does...

A travel case for a 36 key wireless [Corne keyboard](https://github.com/foostan/crkbd) (without the 6th column). The case should fit on top of most standard pitch keyboards (tested on a Macbook Pro as pictured) without pressing any keys and does not...

A minimal, slim case for the [Corne keyboard](https://github.com/foostan/crkbd) (without the 6th column). New version with a switch plate. Note: this case does not leave space for the TRSS jack, it's for a wireless build. ... Hardware needed: ...

This is a custom Corne cherry keyboard case. A similar case of HI-Pro type exists on Thingiverse, but unfortunately, there was no Lo-Pro type available. In response, I designed a new case specifically for Lo-Pro type. You can find a Hi-Pro type...

A minimal, slim bottom case for the [Corne keyboard](https://github.com/foostan/crkbd) (without the 6th column). It has 2mm clearance between the case and the PCB, which is enough for hot-swap sockets to fit. I have a [new...

A case for the Corne LP PCB/plate from boardsource. It may work with other Corne PCBs, but it hasn't been tested. Designed for 10mm round rubber feet on the outer side and M5 screws/threaded inserts on the inner side. PCB is secured using M2...

A Corne/crkbd case featuring:Gasket or Plate MountingRemovable Magnetic Centre-Piece to hold the two halves in placeDXF file for the key plate to allow CNC / Laser cutting in a material of your choice (Designed for 1.5mm plate thickness)Optional legs...

crkbd corne v3 case for nice!nano wireless builds w/ tray for a 304050 600mAh lipo battery. ...m2 countersunk screws required for assembly

Corne 36-keys Chocolate v2.1 case with threaded inserts. ... Needs: - 10x M2 4 x 3,5 mm threaded inserts - 10x M2 6mm screws For the second half simply mirror along the X-axis inside your slicer.

Corne Keyboard (crkbd) Mini CaseA simple case for a crkbd mini with Kailh Chocs and a TRRS connected. I couldn't find another case out there that met all the features I was looking for so I made this.Featuresincluded top plate for Kailh chocs, with a...

This is a remix of the HiPro Case by mburrows with a modification for my specific PCB acquired though Little Keyboards. My PCB has mounting holes that are approximately 4mm in diameter which is much larger than any regular mounting hardware can...

... Case (https://www.thingiverse.com/thing:3652379) by mburrows (go check it out!). ... https://www.thingiverse.com/thing:4229965 CRKBD Bento Case by Kopsi https://www.thingiverse.com/thing:4662203 Corne keyboard (CRKBD) Tenting legs. ... by diagnosis

Corne bottom for this top https://www.thingiverse.com/thing:4459741 Support hotswap socket

Corne slim case. STL files are provided with different tolerance (spacing between pcb and case walls). For me it works the best with 0.4mm, especially after I apply finish it makes no wobble. I recommend to print it with 0.6mm first and then make...

All the changes made from the original are: -Make the external case slightly wider in x and y dimensions to fit the plate (the original didn't fit for me). -Make it taller to half cover mx switches. -Create the spaces for the microcontroller, reset...

Added cutouts on bottom for bumpons and lowered pcb by 1mm

Corne Low-Profile Wireless Travel Keyboard

Separadores para los separadores ;) de mi crkbd (corne keyboard) uso separadores de 10mm y queda bastante bien por favor si los haces comparte ¡¡¡ This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/jPrcXSPIygT

This is a set of two plates designed specifically for the Corne keyboard created by foostan on GitHub (https://github.com/foostan/crkbd). To minimize flex, I've made the midplate significantly thicker at 4.5mm instead of its original 1.5mm...

For crkbd (Corne) keyboard. I'm using crkbd cherry v2.1 PCB. The ramp tenting mechanism is inspired by https://www.thingiverse.com/thing:3473796 Warning: the ramp makes a hollow sounds which you might not like. I'm planning to try a solid ramp...

A modification of the Travel Crkbd magnetic case to fit my wireless corne.I have the battery under the PCB instead of sandwiched between the microcontroller and the PCB.  I also have a little power switch and am using 6mm hex standoffs instead...

I think the original case was designed to have the pcb sitting on the bottom of the case, this caused problems with my kailh sockets, so I used 5mm standoffs. Even so, with these short standoffs I had to dremmel a space for my TRRS cable. ...Like I...

This is a remix of a case for a mini macro keyboard pcb by RyanBates PCB is...

This is a remix of a case for a macro keyboard pcb by RyanBates PCB is...

Inspired by this [oled eclosure](https://www.thingiverse.com/thing:4784085) for the low profile [corne keyboard case](https://www.thingiverse.com/thing:4835208). Printed after rotating 180 degrees on the Y axis. ...Keep the original rotation for a...

I don't use angle TRRS connectors but decided that I could use those extended cut-outs for some tenting attachments. There is a 10-degree and a 15-degree version. They may require some slight sanding to fit properly which should be snug. ... Use 1/2...