corner cable raceway 3d models
149250 3d models found related to corner cable raceway.thingiverse
Made this specifically to hide 5 wire LED cable that runs under kitchen cabinets. Would fit other wire as well, as long as the wire is not too thick - speaker wire and other low voltage wire are good candidates. Each piece is 180mm long, adjusting to...
thingiverse
just a cable raceway. 155 mm long i think. (nope, 159mm long) dont really remember. print shitloads of the hooks and assemble them. with a tool . your fingers may get hurt after you assembe a couple of this. width is 21.1mm . scale...
thingiverse
This modular cable raceway was an idea I had because most cable raceways were really expensive and not modular. More pieces to come in different sizes and uses. ...The countersink hole version is for pan head screws.
thingiverse
Cable raceway for the V0.0/V0.1. ...vhb tape them too the mid pannel and don't make the mistake of printing them in pla (like I did).
thingiverse
Cable management system designed to keep wires neat and tidy. ... Length 250mm x Width 19.6 x height 18.53mm Can be scaled to suit needs
thingiverse
Endcap for cable raceway / channel 60x40 Endcaps are very expensive and they're easy to make
myminifactory
Cable raceway for controlling or disguising cables. 19mm and 24mm wide verions. Stick a piece of double sided tape to the back to adhere to a wall. ...
thingiverse
A c-clamp style cable raceway / tray which clamps onto a desk to hide cables. It features a dovetail on both the clamp and the raceway so they interlock and remain parallel with each other. The screw threads through the clamp and press fits into the...
prusaprinters
A c-clamp style cable raceway / tray which clamps onto a desk to hide cables. It features a dovetail on both the clamp and the raceway so they interlock and remain parallel with each other. ...The screw threads through the clamp and press fits into...
prusaprinters
The plate is 60mm square (2.3in) with screw holes in each corner.I replaced the old 12v lighting in an old RV with LED strips and used this to cover the manufacturer's original large hole leading into my wire raceway. I only used two of the screw...
prusaprinters
Wysokość 60mm i szerokości ( 90mm i 120mm)XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXDownload Wiring strips, (Cable Raceway Conduit) for masking wires and cables, strips are added with a length of 250mm and in the following internal sizes:10mm height...
thingiverse
You can then either lay a cable chain in the channel, or use the included printable clamp to secure your Z-axis wiring out of the way. All pieces print with no support, I use 3 perimeters and 55% infill, though none of the pieces have significant...
thingiverse
How I Designed This I started with a square tube and a slot in one corner to slide the wires in. But felt the build would be a bit complex with supports. I could fix this by two piece design,but I wanted a one piece so dropped the idea of a slide...
thingiverse
This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/0R9bNdbJgP0
thingiverse
to long or to short just import it into tinker Cad and shrink or enlarge it
thingiverse
This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/0R9bNdbJgP0
thingiverse
This is a Tee adapter for the CableHider 1 1/2 inch cable raceway. ...I could not find it at my local hardware store or on their website.
prusaprinters
A raceway for Print instructions Raceway! A raceway for https://www.prusaprinters.org/prints/46970-build-and-have-fun-2 See also https://www.prusaprinters.org/prints/46972-raceway-60 See also the raceway scaled to 60% to fit common metal toy...
thingiverse
I couldn't find a good small cable raceway or cable management system so I designed one based on a large version I bought on Amazon. It's designed primarily for 22awg Arduino wires or a handful of USB cords, nothing too big. I think you could scale...
thingiverse
(2) M4 nuts for Z clamp (4) M4 x 20mm socket cap bolts for cable clamps (1) M4 x 25mm socket cap bolts for cable clamps (1) M4 x 20mm socket cap bolts for cable clamps (4) M4 x 10mm flat head screws to secure drag chains (1) M4 tap for threading...
thingiverse
I built this to aid in keeping cable chain straight. YouTube Channel https://www.youtube.com/channel/UCZ8WG-kqF1kmL2s0xIMfIIg If you found this video helpful or would like help fund future experiments.please donate below. ... Patreon ...
thingiverse
I built this to aid in keeping cable chain straight. YouTube Channel https://www.youtube.com/channel/UCZ8WG-kqF1kmL2s0xIMfIIg If you found this video helpful or would like help fund future experiments.please donate below. ... Patreon ...
thingiverse
These are 2 alternate parts (X90deg and Xrear supports) and 1 new part (plug holder) for the [Drag Chain Raceway for Onefinity CNC](https://www.thingiverse.com/thing:4619804), created by Muddyfeet I really only wanted the Y axis raceway because I...
thingiverse
The parts, along with the parts provided in Thing 4619804 give stl files needed for cable management on the OneFinity X-50 Woodworker or Journeyman. After a couple of requests to modify these two files, to give extra room for the X-50 Journeyman,...
thingiverse
... the rail & cover, mount the rail to whatever it is that you want (using an M3 self-tapping screw) and slide the cover into place. Please note that the cover only slides in from one side as to keep it from sliding the entire way through the raceway.
prusaprinters
... rail & cover, mount the rail to whatever it is that you want (using an M3 self-tapping screw) and slide the cover into place. Please note that the cover only slides in from one side as to keep it from sliding the entire way through the raceway.
thingiverse
Inspired by tried and true cable management solution, the J-Channel Cable Organizer is easy to use and easy to install. It can be installed using screws or adhesive backing. It’s a great solution that makes cable clutter disappear in seconds. ...