corsair obsidian 900d case 3d models

I modified a design from Thingiverse to fit my Corsair 900D case perfectly, sans any screws. I botched the scaling during export, so you may need to amplify it by a whopping 10,000% to get it just right! ...Check out this video for a sneak peek:...

A bespoke façade crafted specifically to adorn the Corsair 900D chassis.

Front door replacement hinges for Corsair Obsidian 550D PC Case Revise the given text by changing the sentence structure and word choice but keep the original meaning intact. ...The revised text should be around 60 words or less.

It's designed using the original faceplate of Corsair Obisidian 650D PC case. The fit is not perfect (just a tad loose) but definitely close enough to keep it in place. Note about the infill: Printing with PLA I found out that it is better to use...

Here are some riser feet modeled to fit the Corsair Obsidian Series 750D full tower case to give the power supply some room to get proper airflow when set on plush carpet. They may fit other cases with square/rectangular feet pads as well. It will...

This is a replacement for the broken rear feet of my Corsair Obsidian 450D mid tower computer case. The model was created using Rhino from the original faulty component, prepped for FDM 3D printing, and exported in various formats. Included files:...

The Obsidian Series 500D is a cutting-edge mid-tower enthusiast PC case featuring iconic Corsair design, smoked tempered glass side doors, and premium aluminum trim. Front plate, roof plate, and door handles add a sleek feel and high-end look. The...

Drive cage support for Corsair Obsidian 750D computer case.

This is a direct replacement for the drive bay door hinge on your Corsair Obsidian 800D case.

Replacement door clip for Corsair Obsidian 450D/750D/900D cases. Remove the original from behind the plastic front bezel. This part just fits in the existing hole. It clips on the door with enough force to be able to pry it off with your fingers. ...

Replacement for 3x 2.5 ssd caddies in the Corsair Obsidian 1000d case. This part allows to replace the 2.5 SSD spots with 3x 3.5 HDD. ...

Drive cage support for Corsair Obsidian 750D computer case. Print Settings Printer Brand: BCN3D Printer: BCN3D Epsilon Rafts: No Supports: Yes Infill: 20% Filament: BCN3D PLA, Tough PLA, ABS Notes: I used 6 layer wall thickness, 0.3mm, Fast...

I'm trying to install a 5.25" DVD-ROM cover on my Corsair Obsidian 700D, but it's not fitting quite right. The same issue should apply to the 800D since they're essentially identical cases with the hot swap drive bay being the main...

I designed this set of brackets as a custom commission to replace a hard-to-find Corsair 8x 120mm fan tray used in one of their massive cases. The full tray is too large to print on most 3D printers (around 500x260mm), so I created individual...

Case Corsair K-761 Here's the revised text while keeping the original information intact: "Corsair K-761 Case." This rephrased version maintains the essence of the original text and adheres to the word limit.

A direct substitute standoff for Corsair's 570X tempered glass side panels, possibly suitable for other cases as well.

Designed to replace the PSU shroud for the Corsair 500D case but may work for other Corsair cases. Added cut-out to show the PSU and extended the length for more space to hide cables and acessories (e.g. ...rgb/fan/usb hubs).

Case Corsair K-243 In this task, you are to rewrite the given text in a different way while keeping the original meaning intact and not exceeding 60 words. ...Here's my attempt at spinning the text: "The Corsair K-243 is a case, featuring a sleek design...

I have a Corsair brand PC case 460X, and it doesn´t fit well in my desk because its height, so i made new feet for it. The feet are designed to fit in the case feet holes and for not to be interfered with the case rivets (marked red in the photo).

Cooling rapidly, this sample of obsidian exhibits a smooth, glassy appearance, lacking the characteristic crystals that form when rocks cool slowly.

Sample of obsidian collected from Millard County, Utah. Specimen originates from the educational resources managed by the Paleontological Research Institution in Ithaca, New York. Maximum length of specimen measures roughly 12 centimeters.

... without the need of too much support material. ... Only support needed it's for "Corsair case feet inner.stl" and only from buildplate, IMPORTANT must print sideways not as it comes from stl. ... 0.2mm of clearance between inner and outside part.

It's uncertain whether this solution will work with other Corsair cases, but if you attempt it, please share your results in the comments below. ... Printer Settings: Brand: Prusa Printer Model: Prusa Steel Rafting: No rafts were used during printing...

A simple headphones stand-holder for the Corsair 570X case. Unscrew the 2 thumbscrews holding the top glass, place the holder and then screw them again. ...Minimal support needed under the arc.

I have a Corsair 7000D that sits on a carpeted floor and I was worried about powersupply airflow, so I created this to raise the case off the floor by a couple of inches.

Corsair case feet to resemble sand crawler MIRROR EACH SET FOR THE LEFT AND RIGHT OF THE TWO MODELS recommend to print tread rollers up for the most detail then glue the two halves together. should screw directly into place. back feet pivot slightly...

I designed this dust cover case for the nintendo switch oled version, inspired by my corsair pc case (4000D) and its hexagonal pattern. The print didn't turned out perfect due to bad calibration, realised mid print and decided to continue. With a...

I built a custom tool to elevate my Corsair SPEC01 computer case off the carpet so the power supply gets air, which is essential when it's mounted fan side down. ... https://www.youtube.com/watch?v=pUoYQkEm9j4 Print Settings: Printer Brand: RepRap ...

Human: This Corsair computer case model boasts an exact scale replica of its original components. Created with meticulous attention to detail, the high-quality design has been perfectly realized in C4D R19. Each and every color element can be easily...

I wanted to finish off my cable management project on a Corsair 570x case with a tempered glass backplate by adding a removable shroud that covers the gap between the cable tunnel and the power supply. This solution consists of two pieces: one plate...