coupons for leapfrog 3d models

I have a lot of problems using PLA on my printer - while looking around for a solution, I stumbled upon: http://creatrtips.freeforums.org/lubrication-egg-pla-add-on-t66.html Not having a Kinder Egg to hand, I decided to roll my own variant. The...

) - http://store.bcndynamics.com/es/mecanica/49-rodamiento-608.html We currently have supports for: 5lb spool - UltiMachine 1kg spool - UltiMachine 1kg spool - BCN Dynamics Universal Spool Support Coming soon: 1kg spool - Leapfrog Adaptors for...

Isolation mount for Leapfrog Creatr. The Creatr feet sit in the 'cup', which is suspended inside the 'ring' by rubber bands. As the Creatr prints, the machine happily bounces around on the rubber band suspension, greatly reducing the vibration noise...

These coupons give you a flat bottom to look at, to verify first-layer conditions, sides to verify good stacking and layer adhesion, and a top with a shallow (0.22mm deep) text to verify the top surface. Set them up with the shown extrusion rates and...

Please visit http://www.reppersdelight.spacymen.com for more information. Instructions Print with ABS or PLA. Use support. ...Mount it in the center of the filament pool rotative platform (see photo).

A simple belt tensioner for Y-axis.

Parts for printing large parts while maintaining a stable temperature in the cabin of work and avoid excessive contraction and expansion of the pieces. ...4mm or 5mm methacrylate plates required are: 370 x 35mm (1 unit) 425 x 35mm (2 unit) 500 x 410mm...

Filament tube guide stopper for Leapfrog Creatr

Leapfrog Creatr lateral arm for 1kg spool. 1KG Maximum. ...No support for printing.

Wade Extruder Support for LeapFrog Creatr This model requires: 2x Screws M3 45mm 2x Nuts M3

Adaption of "Spool holder for Leapfrog CreatR" by Anar, (published Aug 4, 2013). ... This adapter is used to better hold the roll in place.

Quick mounting system for the plates of sides of the printer Leapfrog Creatr. ...Provides quick access to the interior by the sides.

Belt Tensioner for Leapfrog CREATR Z-Axis Print 2 x the STL-File and use a 608 Bearing and 2 Washers.

This optional Sidecooler for the Leapfrog-Creatr i have designed for the Nozzle-Cooler from Zabana. It's cooling down the PLA-Filament from the Extruder-Entry. ... Made for 20mm Fan!

Spool Holder for the Leapfrog Creatr. It's designed for larger spools. You will need a M6 screw and a slot nut (green version, filamenthalterung7.stl) UPDATE (19.06.2014) : The new version (red, spool-holder-No-2) doesn't need any tools for...

Short Demo vid showing vibration dampening performance:http://www.youtube.com/watch?v=iqPYOg69Ngg&feature=youtu.be Print Settings Printer Brand: Leapfrog Printer: Creatr Rafts: No Supports: No Resolution: 0.2 Infill: 100% Notes: You can go for the...

Powerchain support/guide for Creatr from Leapfrog. I made this version cause I want to keep the filament holder and make it printable without support. Warning, with this piece you can't have a modified right extruder ( T0 ). Support de la chaine...

For this extruder load the files and the instruction form ROB65 and replace the two idler-latch-V2-xxx.stl files with my files xxxmsa.stl Additionally you will need one M6 nut! You do not need the washers for the motor mount. This was V1! ... On...

... need supports if your printer is in good tune. These need to be used in a pair, as the geometry is different than the stock carriages. Print Settings Printer: Heavily modified Leapfrog Creatr Rafts: No Supports: Yes Resolution: .2 Infill: 40%

... I have had a leapfrog printer for ages, it always bothered me that the dual extruders prevented me from using the full build plate. This upgrade maximizes the usable size of the build platform. This is only the bearing blocks and the x carriage.

N.b: the instructions are still for v1 but v2 is almost the same (except for the washers when mounting the stepper motor). You do not need to remove any wiring or cut or change original parts. Everything can be restored to its original state if...

This is a major modification of the printer! I have had a leapfrog printer for ages, it always bothered me that the dual extruders prevented me from using the full build plate. This upgrade maximizes the usable size of the build platform. This is...

Pulley for the Belt 3mm - 16 Tooth (945-3M)

brackets for lowering the position of the cable guide

This adapter makes it possible to use flexible filament for you Creatr HS. Just print it using ABS and drill down the holes (2 mm). ...Create the screw-thread with 4 mm.

Because I could only find the one for a single extruder, I decided to design a cooler which will cool both nozzles. Part 1, 2, 3 and 5 can be printed without support. Part 4 has to be printed with support. First place part 1 and 2 from the back...

http://www.thingiverse.com/apps/customizer/run?thing_id=126671 Instructions Using the following options: text_font = write/orbitron.dxf text_height = 8 parts_to_render = 8 text2 = Coupons App text1 = The Project_Size = 125 Render_Quality = 60...

This is a Fan Holder for most of Printers. ...Just put it Where you want. I made it for my Leapfrog Creatr. ...Now with Front Fan's How I Designed This Made with Master CAM.

Cable chain with tube clip for Leapfrog Creatr (left Y axis)

Inspired of the "cable rail" by achilleuss I made a different version out of it. ...With this one you can use the "spring loaded extruder" by Rob65 also.