covers for galaxy note 2 3d models

Stand/Subwoofer for "Samsung Galaxy Note 2"

Galaxy Note 2 Cradle for Otterbox Defender

Case for Samsung galaxy note 2.

COVER Galaxy Note 2 - Samsung

I made this for my Galaxy Note 2 which has a pretty thick rubber case. Because of this, the cradle may be a bit deep for most normal sized phones. While it may not be a snug ft for most phones, it should still hold most them suitably enough. ... ...

http://www.thingiverse.com/apps/customizer/run?thing_id=1665478 Instructions Using the following options: thickness = 2.5 bracket_small_ends = 5 clamp_centering_length = 5 clamp_length = 23 clamp_rotation = 0 smartphone_width = 85 clamp_gap = 0.5...

I also posted a video of the pieces on the pictures here:http://youtu.be/ognuhMpKJsk All the credits for those STL files go for: JadeJak for Low-profile GoPro camera mounthttp://www.thingiverse.com/thing:559610 Datheus for Gopro extension...

Galaxy note 2

Dimensions were taken from an actual Samsung Galaxy Note 2. ...The model is not perfect, but it should be sufficient for designing products around.

galaxy note 2 case with foot Use a 2mm pin to assemble

Galaxy Note 2 Phone Holder for CTC 3D Printer and kompatible. Print out this holder 2x and mount your Galaxy Note 2 in front of your CTC 3D Printer to use them as a webcam. I use the following App: ...

This is a modification of the GameClip to fit the Galaxy Note 2 and 3.http://www.thingiverse.com/thing:43977 Instructions I printed it in standard resolution with 50% infill using MakerWare on a Replicator 2. It took about 50 minutes to print. Not...

... ...Personally, i do not own a Galaxy Note 2, nor have i yet printed this particular file so I'm not 100% sure it fits. I made a model of the phone from some online blueprints, then fit the clip to the model. Should fit just fine directly to the phone.

Design is calibrated for Note 2 but you can remix it for other Note Spens. To have this design to work, you must cut the shiny silver part of the Spen as shown in the video. It will have no effect on function of the Spen. After that to put it inside...

Made at the request of a user, relates to http://www.thingiverse.com/thing:387492 that I made a few weeks ago, which is also available on here if you wish to avoid that link -...

supporto per Samsung Galaxy Note 2

This is a remix of http://www.thingiverse.com/thing:399696 . ...I joined the two halves and resized them to the screen size of the Note 2.

Summary A tool that holds a 8000a/h BW battery close to your note2 by using the two indentions on the sides of your Otterbox case. ...Print Settings Printer Brand: RepRap Printer: Wanhao Duplicator I3 Rafts: No Supports: Yes Resolution: .2 Infill: 100%

A tool that holds a 8000a/h BW battery close to your note2 by using the two indentions on the sides of your Otterbox case. ...Print Settings Printer Brand: RepRap Printer: Wanhao Duplicator I3 Rafts: No Supports: Yes Resolution: .2 Infill: 100%

Galaxy note 2 car holder Instructions You'll find my Galaxy note Holder (this Holder is adapted for the mobile with his case). ...You'll need a 4mm screw and an adapted nut.

Securely mounts a Galaxy Note 2 to any corner. ... Use double sided tape.

Securely mounts a Galaxy Note 2 to a 32mm tube. For other smaller tube sizes, simply make shims to accomodate the diameter difference Instructions Print two C-Clips, re-drill all 8 holes to 3.2 mm and secure with M4 20mm screws (no need to tap). ...Do...

WIP- I wanted a hard cover for my Note 2 but I didn't want to pull off the belt clip portion. I need to round off some of the corners. The notification LED shows up right through the cover quite nicely. ... ...

This is Galaxy Note 2 Case I designed. Enjoy. If you are printing the case in PLA you are going to have to scale it down .25% otherwise it will be to large. ...If you are using ABS you can print it as is.

It's my current case for my note 2. Due to overhangs it prints noticeably rough compared to the Optimus G case. Might clean that up in the future, if my current case breaks. ... Used the inside mesh from this object to get the shape of the phone, but...

For my UP Plus Pro printer I use a special cut/joint to print the 2 halves but if your printer has a larger build plate you may be able to use the single STL. Just added the split halves for those with small build plates. Please be sure to link...

... your feedback. Instructions Printing this with 0.5mm thickness for the bottom, shell and top should be enough. I use a infill of 30% to get a nice strong part, but it will work with 20% infill as well. ...I'm using a fan to get the overhangs right.

... your feedback. Instructions Printing this with 0.5mm thickness for the bottom, shell and top should be enough. I use a infill of 30% to get a nice strong part, but it will work with 20% infill as well. ...I'm using a fan to get the overhangs right.

I didn't like the original Samsung dock for my current phone so I decided to make my own. Some of the features I think it should have are that it must be fully useable also in the dock. So I made some openings from the back to the front to have...

I didn't like the original Samsung dock for my current phone so I decided to make my own. Some of the features I think it should have are that it must be fully useable also in the dock. So I made some openings from the back to the front to have the...