cpu adapter 3d models
119201 3d models found related to cpu adapter.thingiverse
Searched for a brace for my Amiga 2000 Cpu Adapter V2.0(designed by Matthias Heinrichs). Only found one that looked like it could fit, but it was too long. Long story short, this remix is only 59mm long. I screwed it with a M3x15 hex bolt direct...
thingiverse
Corsair H100i AMD CPU socket adapter. AM3 & AM4 *use Intel hardware for mounting (thumb-nuts, standoffs and screws) 28OCT18- Updated the design to allow for the Corsair Link cable to be plugged into the pump...my earlier revision did not have...
grabcad
Adapter for Hyper 6 CPU cooler. The part connects to cpu cooler with 4 3mm bolts through 4mm holes (57x57). It is manufactured from plastics, with CNC drill (and little handwork of course). Connection to motherboard is with 3mm bolts at 75x75. The...
thingiverse
Before making the adapter, I had the standard solution of bending the rubber attachment feet around the heatsink to get it to stay on. It worked, but not well, CPU temps were around 48 °C at idle. ... After making the adapter to hold the fan right up...
thingiverse
Adapter to mount a 120mm fan where normaly a 92mm fan is installed. ...I use this on my desktops PCs CPU to reduce noise level.
thingiverse
Customized version of https://www.thingiverse.com/thing:21112 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=21112
thingiverse
With this you can adapt/upgrade a cpu cooler that uses a 70mm fan to use a 80mm fan. ... Larger fans are usually quieter and easier to find.
prusaprinters
An adapter to use a Noctua 60mm fan on a CPU cooler that only accepts 50mm fans. Specifically designed for home lab server from Supermicro - SYS-5028D-TN4T.</p><p>Should fit almost any cooler for the FCBGA 1667 socket (Intel® Xeon® processor...
thingiverse
Remixed fan adapter to reduce plastic usage and smooth out the circumferences.
thingiverse
This is an adapter to mount an Intel type heatsink to an AMD AM3/3+ motherboard using a 120mm fan.
thingiverse
Hallo, ich hab hier mal ein Adapter entworfen um z.B. AM4 Wasserkühler auf ein AM4 Board zu verbauen. ... Das Teil einfach 2x ausdrucken und mit M3 Zylinderkopfschrauben direckt in das Kunstoff schrauben.
thingiverse
This is a simple adapter to use a 75mm cooler in a 80mm holes, see pictures to understand. Also you have a separator, cause you probably need to up the alu plate. ...Give it the height you need with your slicer.
prusaprinters
I printed this out of Atomic Filament Carbon Fiber PETG for some extra thermal protection on the CPU heat sink.Use the stock CPU fan screws to bolt the adapter to the heat sink and the stock Noctua screws to mount the Noctua fan to this adapter. It's...
thingiverse
This variant is a print of the original Solder Fume Extractor at 68 percent using an old CPU fan (which is an 80 x 80 fan). This CPU fan however as you can see has a bit larger fan cage due to the design. This piece I designed goes between the fan...
thingiverse
This is an adapter for 486 AMD-X5-133 for installing socket 7 heatsink on socket 3 motherboard.
thingiverse
... Adding more spacers will loosen the contact on the CPU. You should use them if you feel that you are applying too much force on the tightening latch when attaching the heatsink. I recommend ABS for heat resistance. PETG would probably be fine.
thingiverse
... --- This is an adapter for shifting a 92mm CPU fan 7.5mm in one direction. In my case, the Gigabyte x570 Aorus pro-wifi itx features a structure which prevents the Alpenfoehn Black Ridge CPU cooler from being mounted in it's default configuration.
thingiverse
An adapter to allow the factory CPU blower fan to be replaced with a standard 80mm fan on a Dell Optiplex 9010. I believe the heatsink is a Dell J50GH heatsink. I'm converting this old computer for other purposes and would like to make it near...
thingiverse
if your board is dense, there may not be room around your heatsink to mount adapter. VERSION 2: This Version is designed to mount to Heatsink by friction fit over the mounting screws of the heatsink. the best option for a densly populated board...
thingiverse
... less than 80mm. b.) cut the cpu fan as shown in the picture, make sure the tab are maximum 7mm long c.) print the adapter d.) assemble the parts, use glue (i use revell contacta professional) edit 07/02/2020 as suggested added the intake version.
thingiverse
This fan adapter lets you connect a computer fan to a pipe. I think most computer fans are the same. The pipe is a 1 inch pipe so it has and OD of 1.315 inches. ...Get a union or an elbow with a 1.315 inch ID; this will fit inside snug.
thingiverse
This is a am4 adapter for EVGA CLOSED LOOP CPU COOLER 120MM
thingiverse
A simple adapter to turn a CPU fan into a 92mm standard fan. Fits Intel D34223-002 12V 0,45A fans, may fit other fans of similar construction with ~88.4mm outer diameter of mounting legs (not the fan blades!) For installation you will need to cut...
thingiverse
Offset Adapter to enable 2x120mm and 1x120mm CPU Water Coolers to fit in awkward cases. Adapter is mounted onto Water Cooler using the normal screws supplied with it and is then mounted to the case using normal case screws. The adpater moves the...
thingiverse
Inspired by this adapter https://www.thingiverse.com/thing:4138132 but I didn't want to break mine so I came up with the first version adapter (picture 3), but before printing it I thought I could design another model that used less material...
cults3d
I came up with the first version adapter (picture 3), but before printing it I thought I could design another model that used less material (picture 4) I only printed the second version but the first should work just as well since I used the same...
pinshape
[At the same setting, only changing the presets in Prusa Slicer 2.2.0, the PLA version came out with a little loose tolerance, you might want to scale it down by like 0.1%-0.5% to get a tight fit, or just use a thin rubber ring around the prongs]...
thingiverse
An adapter use to install 80x80mm fan into 90x90mm CPU cooler
prusaprinters
Keep using these CPU coolers on old motherboards even if the original rubber-mounted custom fan is broken or lost.I tapped the fan mounting holes with ISO M4 but the self-tapping screws included with most PC fans should work just as well.