cr 10 fan upgrade 3d models

WARNING: This may not fit on Ender3 Fan/Hotend Stock configurations because of its height. Ender3 Stock Airflow has 9~10mm Height, this remixed version is around 16mm height. Check your nozzle height from Airflow piece before printing this version or...

I've discovered a common problem with many circular fan ducts - the nozzle often isn't even remotely centered, so I built this one from scratch. To ensure optimal performance, I also designed the interior to cool the filament evenly on all sides.

I was really excited about this fan nozzle design, but unfortunately, I found two major issues. The screws were too short to fit into extended wells, which was a huge problem for me. ...Additionally, I noticed that the model was missing the rounded...

Two small aluminium tubes are held by a plastic holder that forces all the air from the radial fan into the tubes. There are small holes along the tubes blowing the air down over the printed part. You'll need two 30 mm long aluminium tubes with a...

I was unimpressed by the fang designs available here, as many wouldn't accommodate my larger Noctua A4x20 fans, which stand at 20mm high. Others weren't optimized for airflow. So I drew inspiration from a few different models and created a custom...

This is a simple remix of Midevil1's fab 120mm fan base. It simply has the addition of small dovetail locking pieces to ensure they cannot come apart. The dovetail recess is 0.2mm larger diameter than the dovetail so this should account for printing...

This is an enhanced version of Midevil1's popular 120mm fan base design, featuring small dovetail locking pieces for added security and reliability. The dovetail recess has been carefully crafted with a diameter that is 0.2mm larger than the...

A hole lets me plug in the Micro USB of the pi for power, another hole allows fan wires to pass into the same compartment. There's also a hole to pass power from the control box; alternatively, the "ExtPower" base version has a 15mm hole at the rear...

... and easy Fan Duct. ... Makes it simple to use the Creality stock housing with the 5015 Radial Fan Upgrade. Perfect for: CR-10 Ender 3 Ender 2 No supports required! Attaches directly using original bolts. ... New, updated V2 design improves airflow.

Ender 10S Upgrade Power Supply Control Unit Stand Best Creality CR-10/S/V2 Upgrades & Mods elevates the control unit about 2.8 inch - 7.3 cm helps in good unit ventilation and better cooling easier access to the sd card avoid grounding electric...

This is a Circular Fan Duct designed specifically for the CR-10 Series. Although it was originally created for the CR-10 S5 model, it works seamlessly with every CR-10 variant. V1.0 - Initial Release (February 21st, 2018) If you appreciate this...

This is a circular Fan Duct for the CR-10. This was designed for the cr-10 S5, but it works for pretty much every CR-10. ALL NEW VERSIONS WILL ONLY BE AVAILABLE AT MyMiniFactory!: https://www.myminifactory.com/object/3d-print-57338 V1. 21/Feb/2018...

This is a circular Fan Duct designed specifically for the CR-10 series, initially created for the cr-10 S5 model but suitable for use on pretty much every CR-10 variant. ALL NEW VERSIONS WILL ONLY BE AVAILABLE AT MyMiniFactory! 21/Feb/2018 First...

Fan Mount for CR-10 / CR-10S Plus BLTouch (PWM Fan 5015, 12 Volts)

I install the factory-installed fan and it performs significantly better.

... first to expose just the knobs and circuit board. Some adjustable legs were added to give it a bit more height as well. By doing so, I made it possible to utilize cheap fans that were lying around while still maintaining a quiet environment.

Tronxy XY2-Pro Fan Upgrade, Reimagined from the CR-10. ...In Action: www.youtube.com/watch?v=MfUduM3yqPo

CR-10s Pro V1, CR-10s Pro V2 and CR-10 MaxMaintenance, trouble shooting and upgrade guide …now following some facebook forums and other chatrooms it seems, that there is always a core set of things which are repetitively asked, so I decided to...

To upgrade your CR-10's cooling system, using the original stock hotend, you'll require two 40x20mm blow fans mounted side by side.

all in one cr-10 Hotend cooler - printable without fan

Adapter for upgrading a 40mm fan to a 50mm fan on the CR-10, Ender-2 hotend and filament cooling system designed by Rocco81-92, available on Thingiverse under ID 2751027.

To upgrade the CR-10's cooling system using its original stock hotend, two 40x20mm "blow fans" are required and should be positioned side by side for optimal airflow.

Remix of a CR-10 Fan mod for the CR-10 5s. ...Sits lower and sets the nozzle more center of the fan mod.

Porte ventilateurs CR10

Porte ventilateurs CR10

Single and Dual 4010 fan duct for CR-10. ...Ender 2,3, pro, 5 etc.

Remix of a CR-10 Fan modification tailored specifically for the CR-10 5S. ...It lowers the fan's sitting position, aligning the nozzle perfectly at the fan's center.

This is a remix of an all-in-one part cooling duct for Ender/Cr-10 style hot ends. It is resized to fit the cooling fans that are coming on the newer Ender 3's with wider tabs. Print in PETG for best performance, although I did the first in PLA...

This is a rewritten part cooling duct designed for Ender/Cr-10 style hot ends, now resized to fit newer Ender 3's with wider tabs on their cooling fans. ... Print it in PETG for optimal performance, as I initially did the first one in PLA and it lasted...

This is my remix of "HallON v3 holder for Ender 3" for AYF Creality CR-10 5015 Fan