cr 10 v3 upgrades 3d models

Linear rail bracket set I designed for the CR-10 v3. You will lose about 30mm of y-axis on print bed. I pared this down as far as I could without compromising support and integrity. Without the loss the left carriage/bracket will hit the stepper...

CR-10 V3 have some issue with filament sensor giving too much drag & strain on the filament I designed this mod so i can mount the sensor directly under the filament spool I never had to print things higher than 300mm, but you should note that this...

The filament sensor on the CR-10 V3 is has a mechanical flaw that can cause one of the following to happen: - you can't insert filament through the sensor (jammed) - the sensor indicates no filament when there's filament in there, which can happen...

... for air flow. - On the opposite side close all openings and holes with tape - place two 120mm fan's on the new bottom plate. Put 2x 12V fan's in series to use original 24V - Screw all togeher and hear the silence It's designed to print on CR-10 v3

CR-10 V3 pi mount that clears the support arm and no hardware is required ! I hate when I have to track down nuts and bolts, etc.. This holds my pi cam v 1.3 perfectly and allows me to adjust the lens focus without removing the camera board. You...

This thing allows you to mount a Phaetus Dragonfly BMO to your CR-10 V3 without the bulky stock housing. The fan mount can be used with the stock hot end as well. I wanted to have a mount for the fans that wasn't integrated in to the hot end...

Recent adventures necessitated I move from my Robo3D R1+ (an antiquity at this point) to a newer platform - hence the CR-10 V3 (I like direct drive). Having already printing a [cable chain](https://www.thingiverse.com/thing:4725258) to fix an...

For the CREALITY CR-10 V3 printer. The original Creality Silicone Dampers are too short for this printer resulting in the print bed being too far away from the nozzle. This spacer fixes the issue, fits perfectly into the Creality damper and moves the...

CR-10 M4NOT COMBATIBLEAny Ender 5 model, Any Ender 3 V3 model======================================================================================================= BILL OF...

This adapter plate offers the possibility to install a BigTreeTech SKR2 mainboard in the electronics housing of the CR-10 V2/V3. The plate is screwed in place of the original mainboard (Creality V2.5.2) with M3 screws (use the existing screws) and...

This is a 120mm fan adapter for the new style CR-10 V3 control boxes with 2mm cooling holes on the sides instead of slots. It snaps securely into place and replaces both the 50mm and the 40mm Creality fans. Please be aware that the power supply...

If you want the longer sides front and back, check out this remix: https://www.thingiverse.com/thing:4864920 Complete system to mount a BIQU H2 to a Crealty CR-10 V2 or V3. Route heater and thermistor wire between mount and plate. Heater wire...

If you want the longer sides front and back, check out this remix: https://www.thingiverse.com/thing:4864920 Complete system to mount a BIQU H2 to a Crealty CR-10 V2 or V3. Route heater and thermistor wire between mount and plate. Heater wire should...

Remix of CallJoe's Creality CR-10 Bed Leveling Indicator V2, modified to fit above the air cooling exhaust for a sleeker design.

This is a set of clamps designed to replace the hinged metal glass clips included with the Creality CR-10 V2/V3. These clamps will hold your glass in place with the added benefit of not obstructing **any** of the print surface. Never worry about...

With that in mind, I've created a new spool holder that slides into the 2020 v-slot extrusion on the top of my CR-10 v3 printer. \#1 is solved but it simply sliding to clamp the spool in place, and \#2 is solved by having two "rods" instead of only...

... infill is recommended, with 100% on the duct. No supports are needed except for the direct drive mount. I always raft the parts. After the direct drive upgrade, you can reduce retraction significantly or entirely if you don't mind some stringing.

1) Firmware gently provided by Nic, it made a custom one(that I'm currently using) for our cr-10 v3 with e3d hotend. It has numerous versions, with bl, no bl.. etc. Reach out to his group for it...

this is a mod made for the cr 10 v2 and 3 as a flat design you can use to cut out and fold for metal and other materials you can get to work https://youtu.be/uubrlFYza9Q video link standoffs for screen and mother board files are also included

This is my first crack at a cable anchor/tie for my CR-10 V2, which is using a direct drive mount and had no convenient place to tie wires. ...I'm definitely still working on this one, but the current revision works rather well.

Design to mount a Voron Afterburner on a CR-10 v3. For BL-Touch mounting, it can be left off, or use the bracket that comes with the kit (or available as [Thing 3940873](https://www.thingiverse.com/thing:3940873)) There's also a cable...

My CR-10 doesn't come with the smaller knobs that many are press fitting into these larger knobs. Honestly, the original knobs that come with the printer aren't all that bad but i really like this design. it gives you about 10mm more diameter and i...

The author provides good information at this post: https://www.thingiverse.com/thing:4786557 I also printed the 608 bearing from Xtrudor found here: https://www.thingiverse.com/thing:3002837 My contribution was to bring together a fully printable...

Bottom part comes togheter without zip tires or bolts plus the top part was redesigned to better fit cr10 v3

Simple filament guide for CR-10 printers. Tried to design it without a nut and bolt, but didn't work out as planned, so I added a printable one. Edit: Designed a redesigned bolt with an octagonal head and tighter tolerance on the nut. Edit: Added...

I looked around for a mount to test the Biqu H2 tool end on my CR-10 V2, but decided to create my own. I designed this based on the Biqu H2 dimensional step file available on Grabcad and verified the measurements once the actual tool end arrived in...

So this is just a quick one which fits my needs. You need: 8x M3 nuts 8x M3 8 screws 1x 10mm bowden pushfit 1x cable chain (https://www.amazon.de/gp/product/B06XKZ35VH/ref=ppx_yo_dt_b_asin_image_o02_s00?ie=UTF8&psc=1) I printed all parts without...

Here is my improved filament sensor for Creality CR-10s made with guide wheels specifically for the Direct Drive machines with overhead mounts. ... Use your sensor and screws from original run out sensor, and print parts as listed, you will also need 2...

Designed up this fan duct as I bought the CR10 V3 and the extruder was very frustrating to access when needed. Hot end cooling fan cowl is optional, i thought it looked pretty. ... Please note this is a work in progress, I'm still testing and...

I was thoroughly impressed by the v3 fang, and as such, I took it upon myself to reimagine its design on a smaller scale - specifically, a 40mm version. ...The results have been nothing short of outstanding, though it's worth noting that my testing has...