cr 10s filament guide 3d models

You're looking to utilize the large filament spools with your CR10S PRO 3D printer. ...Indeed, it resembles an adult toy, but rest assured, it functions effectively.

... the filament holder for my printer. ...first i have centered the filament spool so it will not drag to the side. then i added bearings so it will roll quietly and effortlessly. ... all fasteners originated from Aliexpress and cost around 2~4 USD total.

The parts that build the walls of the base require the following: 60mm_support_Front_corner_mk2.stl - one for each corner 150mm_angle_vent_panel_mk2.stl - two for each side 85mm_center_support_side_panel.stl - one needed for each side...

What I really needed was an extruder visualizer that could show me if the filament is actually moving through the tube when the driven wheel turns. But I couldn't find anything like that for my specific printer. So I decided to create one myself. I...

Here's a customized GoPro mount designed specifically for the CR-10 3D printer. I carefully crafted this model to eliminate the need to remove leveling screws, instead relying on friction to secure it in place. This makes installation and removal a...

This filiment holder/dispenser is designed to fit snugly onto a Creality CR-10 S pro 3D printer using the OEM angle bracket and quick disconnect nut, providing a seamless integration. Three 22mm bearings are utilized, which can be sourced from local...

The Original Spool Mounting that the CR10S Pro came with created a bad angle that caused the filament to rub on the filament run-out sensor. So 3DSanz created a mount for the side of the frame which looks really good but causes a good deal of...

I designed this 120mm fan base to combine two 120mm fans on my CR10S and minimize filament usage. It took roughly 7 hours to print and around 50g of filament. The design features a right end, a left end, and a center bracket. Brackets are screwed...

I wanted a sleek, lightweight frame brace design for my CR-10. I found Rick's design, which I really liked, but it's in inches and I found it a bit challenging to install since he designed sockets for the nuts at both ends. So I created my own frame...

Make sure that all holes in the fan shrout are open and clean of filament - if everything is mounted correctly, the fan is very sufficient, I only need 25-40% cooling on PLA, otherwise I get layer adhesion problems. Mounting is a little tricky... 1)...

Time to print some new ones using flex filament - problem solved! I had a similar experience with rattling noises coming from my own bed leveling knob upgrades, so I took matters into my own hands and designed these custom solutions to put an end to...

Just for the Max! ...You can add split keyrings to protect it from friction as shown.

bold and window

Just for the Max! ...You can add split keyrings to protect it from friction as shown.

CR-10S PRO Upgrade

Mount a BondTech CR-10S to a roller using a custom designed filament guide specifically made for the CR-10S. This guide ensures smooth and uninterrupted printing by keeping the filament aligned with the rollers, reducing wear and tear on the...

A remix of the Ender 3 Filament Roller Guide [http://www.thingiverse.com/thing:3052488] adapted to fit the CR-10 v2. This fits on the stock filament runout sensor shell. 10/6/20: v4.5 now has been uploaded, with the requested beveled/chamfered...

Human: A revised remix of the Ender 3 Filament Roller Guide [http://www.thingiverse.com/thing:3052488] tailored for the CR-10 v2. This fits perfectly onto the stock filament runout sensor shell. For some reason, only three out of five parts are...

This is a remix of [franpoli](https://www.thingiverse.com/franpoli)'s fantastic filament run-out sensor/limit switch bracket designed for the Creality CR10S, CR10 and Ender 3 with direct drive solutions.\r\n\r\nMade to accommodate the switch used in...

CR-10S-Bondtech-Mosquito_Mount_-_Bl_Touch

Fan replacement for motherboard CR-10S Pro

To calibrate and fine-tune my printer, I rely on the following straightforward guides: https://www.3dhubs.com/talk/t/howto-calibrate-tune-and-fine-tune-your-printer-and-filament/5695...

The evolutionary spool holder is designed to work seamlessly with multiple Creality printers, including the CR-10, CR-10s, CR-10s Pro, and Ender models. ...It's built to fit onto the original bracket of these machines.

The original Cr 10 S filament roller guide, designed by OneBadMarine, can be found on Thingiverse at https://www.thingiverse.com/thing:3184808. ...This guide is intended for use with the Ender 3 Filament Guide created by MattEllison, available on...

Kamera Halter für Unifi G3 Flex am CR-10S

Leveling knob for Creality CR-10S https://youtu.be/G5S57LttreM Creality's 3D printer outshines all expectations! I firmly believe this is the top-notch printer available within its price range, and it's now highly recommended by the community as the...

This is a direct replacement for the CR-10S Z Endstop Mount.

CR-10S PRO UpgradeThe product cannot be discarded.Let's proceed with product design and upgrade

This is my first upload. ...Display Cover for my Creality CR 10S PRO V2.

CR-10S PRO UpgradeThe product cannot be discarded.Let's proceed with product design and upgrade