cr10s pro octoprint 3d models
74823 3d models found related to cr10s pro octoprint.
thingiverse
I found the really cool project to use Octroprint to measure temperature and switch a relay board: - https://www.thingiverse.com/thing:2245493 To control my printer, I use Octoprint anyway, and I like the possibility for an automatize a temperature...
thingiverse
Ideal behind this project is to use a Raspberry with Octoprint and measure the Temperature of my Printing-Case and control a fan with the used hardware. I prefere a USB Cam with this camera holder, to have more flexibility to position the camera....
thingiverse
Boitier pour serveur Octoprint CR10S PRO Fichiers : Boitier Pied de caméra Boitier Caméra Capot Logo Octoprint Guide de collage du logo Pré-requis : Caméra USB Lecteur de carte SD Visserie Pistolet à colle Colle Coude USB Raspberry PI 3 Câble USB >...
thingiverse
This remix is one based on Anscari's "Cr10s Pro Fan Duct". I had a couple issues with his otherwise very well put together remixx of siteswapjuggler's work. First was the fan duct hung a little too low and actually would have collided with the bed...
thingiverse
Simple bearing based roller for the CR10S PRO filement holder. ... This can replace the static roller
thingiverse
CR10s Pro filament spool fixture, wheel holds 2 608 bearings. Simple design. enjoy! ...
thingiverse
As I could not find a model for my recently acquired CR10s Pro hotend, I quickly designed this in Fusion 360, this model is size accurate, as I designed it with a CR10s Pro in one hand, and a caliper!
thingiverse
Remplacement facile du filamant sur CR10S Pro avec cette pieces en quelques secondes https://youtu.be/LxGfK56k-Ug
thingiverse
modified for the ender 3 microswiss dd to fit cr10s pro. ... had to raise bed 5mm set x axis off set to -35 and y to -25
thingiverse
It is the optimized variant of a fan duct. ... Fits the standard fan 40x20 of the CR10S Pro V1/V2. You can use the original screws. ... Material: PETG
thingiverse
Save or repair bad wire on Auto Leveling Sensor on CR10S PRO. ...Utilize zip ties to hold in place and cover with wire sheath.
thingiverse
Yet another cooling fan duct for the CR10s_PRO. I printed few other fan ducts but none was a perfect match - I guess Creality changed the fan design or something. ... Anyhow, this one fits good for me.
thingiverse
Conic filament feeder for Creality CR10S Pro. I've included 2 different versions depending where your filament spool is located (on top or bottom). Glue part 1 and 2 after printing. ...No support needed.
thingiverse
This is a spool holder for a creative CR10S Pro. I wanted my filament spools to be able to unwind smoothly so I made this little bearing mounted reel. ...It works tip top
thingiverse
Pièce de renfort de l’imprimante CR10s PRO L'installation des pièces inférieure oblige à percer la base de l’imprimante pour un meilleur maintien. ... il vous faudra une tige filetée en M10.
thingiverse
Modification for the CR10s Pro Extruder. The connector kept damaging the PTFE Tube. ...Didn't have a problem with my Ender 3, so I adjusted the clamp to fit the PTFE coupling from an Ender 3.
thingiverse
Support d'angle pour CR10S-PRO ,avec le trou pour fixation avec la vis d'origine . ...je l'ai imprimé avec du PLA et c'est niquel , depuis le plateau ne bouge plus latéralement !!!
thingiverse
This is a handle I made for the CR10s Pro Wrench. The small wrench is going to transfer a lot of heat. Don't burn yourself. ...Use this handle when changing your nozzle and hot end.
thingiverse
Filament guide for Creality CR10S Pro - easy install 1. remove the 4 screws of filament sensor 2. install the part (push it on the filament sensor) 3. ...screw the filament sensor on - self-tensioning solution - print duration less...