cr10s upgrades 3d models

This creation was built using the innovative tools of Tinkercad, a leading digital platform for designing and editing 3D models. ...You can instantly edit this design online at Tinkercad's official website, https://www.tinkercad.com/things/2BvAbHW798b.

A 2-in-1 upgrade for Creality CR10S and possibly other printers. Direct drive and auto leveling using nozzle. Uses the SIMAX3D Dual Drive BMG Bowden Extruder 1.75mm High Performance Upgrading Parts for CR10, Ender 3 Series, Wanhao D9, Anet E10,...

Direct drive and auto leveling using nozzle. Uses "SIMAX3D Dual Drive BMG Bowden Extruder 1.75mm High Performance Upgrading Parts for CR10,Ender 3 Series,Wanhao D9,Anet E10,Geeetech A10 and Other DIY 3D Printer kit" from amazon.com:...

It works perfectly fine. Extending the stepper motor cable, drilling a few holes... What's going on with the Z-axis on this printer of mine? After every print job, the right side is 2-3 mm higher and needs to be re-adjusted again. Apparently, the...

Due to these significant upgrades, I could no longer use the original electronics box that comes with the CR10s, making way for more advanced components. This comprehensive upgrade includes a wide range of essential parts necessary to secure my...

A upgrade for the Creality Cr10s printer to get dual extruders. Printing: Infill - 20% layer height - 0.2mm outer layers - 4 This print is based around the standard creality 12V extruder like this one:...

Needed: 4x M5x8, 4x M3 bolts for the rail, 4x M3 nuts, 2x M5 nuts, and 4x 2020 T-slot nuts. I cut the original carriage screws to length. The assembly works with the end stop switch in its original position. ... The rail I used is available at...

Needed : 4x M5x8 , 4x M3 bolts (for The Rail ), 4x m3 Nuts ,2x M5 Nuts 4x 2020 T-slot nuts i cut the original screws from the Carriage to length it works with the original placement of the End stop switch https://tinyurl.com/y5987m2c (the Rail i...

When installing the CR10S Direct drive upgrade, print out the parts specifically designed for your machine and fit them accordingly. You can then use a levelling probe without needing to update your firmware. ...The Y component replaces the holder that...

The part cooler is able to be removed and replaced easily or upgraded later (New designs are in the works). This has been designed and tested to make sure the stock fans fit properly. Also included is a BLTouch mount that can be slightly adjusted...

This is a replacement fan duct designed specifically for the CR10S-Pro 3D printer. The source project can be viewed at https://cad.onshape.com/documents/9526b4e542a64217ae81de98/w/35ceba875888c9774892aad1/e/b9aad334de9abecdee01efcf. Version V1...

The Bondtech Direct Drive Extruder, specifically designed for the Creality CR10s Pro, was unveiled in May as a cutting-edge solution that brings direct drive technology to this popular 3D printer model. At its core, this extruder leverages a powerful...

I created this control box case because I wanted to reduce the noise of the control box fan by replacing all original fans with Noctua fans. The original 60mm fan is only 15mm thick, but the Noctua fan (A6X25 PWM) is 25mm thick, making it impossible...

Insert two worn bearings from an old skateboard wheel or a 3D printer's nozzle. ...Alternatively, purchase two new bearings measuring 16mm in diameter by 5mm thick.

The MK8 Hotend upgrade is a perfect fit for the CR10S, CR10, and Ender 3-5. It works with all MK8 Hotend's (Red). A fan for the hotend comes in at 40x40x20. M3x30mm screws are needed for mounting. The stock fan is included. There may be an issue...

I made a little upgrade for the CR10S-PRO filament sensor after experiencing some issues with TPU flexible filament slipping below the sensor microswitch. **CAUTION** This part is slightly oversized, so you'll need to sand it down to get a perfect...

If all fans have been upgraded to quieter 12V alternatives in your printer, this solution offers a controllable parts cooling fan that can be run at much slower RPMs, greatly reducing noise levels. This project comes with a Fusion360 project file,...

This gantry square was originally designed for the Artillery Sidewinder X1 by Ethereal Project (YouTube linked below) and I modified for use with the CR10s-Pro. It 's used to square up your X-axis to the Z-axis when installing a Z-Sync kit like this...

This is a remix of my previous Hero Me remix which works with the BASARABA INNOVATIONS USA Direct Drive upgrade kit for the Ender 3, Ender 3 Pro & CR10S. This remix involves the base unit (2 versions), Dual 4010 fan duct and the dual 5015 fan duct....

This is a remix of my previous Hero Me remix which works with the BASARABA INNOVATIONS USA Direct Drive upgrade kit for the Ender 3, Ender 3 Pro & CR10S. This remix involves the base unit (2 versions), dual 4010 fan duct and the dual 5015 fan duct....

Pro Fan Duct CR10s Upgrade\r\n\r\nJune 5, 2019 Upload

cr10s spool upgrade kit precision crafted for ultimate performance\r\nsecure the sprocket with high-quality tape as shown in accompanying image\r\nyour feedback is greatly appreciated, please share your thoughts below\r\ngrateful for your support

Quick clip I made to channel cables on CR10S-Pro upgrade. ...Add a magnet into the bottom and can attach on base and up frame if required.

Customized version of https://www.thingiverse.com/thing:34558 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=34558

guida filamento per stampante cr10s, facile da installare, non servono viti, montaggio ad incastro

... challenge, one must have access to a lathe. Since modifying my CR10S and Ender 2, I've encountered no issues on either machine, which have both printed for approximately 400 hours each. ...Designs are available in DXF and PDF formats for easy use.

This Model is perfect for the use of your CR10S inside a housing, if you havn't enough space for it. I designed it to screw it into the holes of the rubber feet, with the original screws. ...In the best case you use a cable extension, to be sure you...

This Model is perfect for the use of your CR10S inside a housing, if you havn't enough space for it. I designed it to screw it into the holes of the rubber feet, with the original screws. ...In the best case you use a cable extension, to be sure...

... to 50, 10% fill. 6.04.19: The final version increased the foot side to 22mm for an easier fit over the CR10S rubber feet. The feet fitted and controller fits under the printer now. ...Next up is moving the print spool and tidying the cabling.

Human Upgrade: Slingfire Module Activated.