craftbot 2 3d models

Update 2020-12-13: I made the pin holder a bit tighter/shorter so that the pin can go a little bit more through the small hole. That way clearance between the wiper and the BLTouch pin can stay as it is. When removing the holder, press the sides,...

PRINTinZ Plate Hold Down Clip for Craft Users

Printable without any support. This was designed to allow all the tools in the blue folder to be mounted on the side of the printer. I just used some slightly longer M3 screws to secure it. Printed in PLA, 15% infill with no support. I did...

Designed this up for a bit of fun... You will need to glue some bits together.. have fun :-) The only thing you need to print with support is the main printer and the X rail, I've included 'support' in its name to remind you. I printed this...

The enclosure's heat was causing the printer door to sag under its own weight due to worn-out hinges. To prevent it from falling or swinging open, a simple support system was implemented underneath the frame of the printer. This basic solution would...

Remix of the camera holder to double arm so that a HERO4 is centred regarding the build plate.

I created this adjustment aid to ensure my XY frame and build plate are perfectly parallel, as they were significantly misaligned at my CB3, preventing me from leveling the bed correctly - it should work with most calipers. ...After taking measurements,...

Simplified Model for Verifying CraftBot Bed Calibration. Two-millimeter line width indicates a probable five-extrusion setup. ...The bed height stands at 0.6 millimeters, allowing for early cancellation if satisfactory results are achieved.

A simple mod allows you to position your filament spools on top of your machine. This enables easy access to swap out rolls and keeps the printer's footprint down to a minimum. You will need a few extra screws to attach this modification. I used ten...

Designed this filament holder to allow both filament spools to be placed at the back with easy access to change them. This can be used with the dome as in the photo. I printed these in PLA at 60% for strength, been using a few weeks now without...

Attach the holder and screw mount for the Pi B+ sleeve to a solid base by gluing them tightly together, then secure with screws once the adhesive has fully set.

Remix of the camera holder to double arm with GoPro mount so that a HERO4 is centred regarding the build plate. ... Best frame working with this mount: https://www.thingiverse.com/thing:4279590

I ruined mine by applying a bit of pressure, so I reinforced it. Again - a hack using netfabb and not entirely well-aligned parts. I pieced this together from these two Things: http://www.thingiverse.com/thing:619684 and...

Holder and screw mount for Pi B+ sleeve (http://www.thingiverse.com/thing:604915) Glue them together and screw on.

#### Additional materials: * __12x M3x10mm screws!__ (This might be overkill and is probably going to be reduced in future designs.) #### Compatibility (these are examples, there are probably many more): __bar type-A__ [M6 thread]: * Alfawise: U20,...

Another version of Garmin Fenix 3 wristband - with Voronoi pattern. ... Printed in TPU. Due to multiple retractions print very slowly. (I did 12mm/s on Craftbot 2)

Another version of Garmin Fenix 3 wristband - with Voronoi pattern. ... Printed in TPU. Due to multiple retractions print very slowly. (I did 12mm/s on Craftbot 2)

2

2

2

2

2

2

2

The design "Human: 2" was created by Romanov using the 3D modeling software 3DTin.

Crafted by: xyd Developed with Cubik Studio 2.9.480 Beta

http://www.thingiverse.com/apps/customizer/run?thing_id=273099 Instructions Using the following settings: Letter depth = 2 Border distance = 5 Border radius = 10 Base depth = 2 Y name 4 = -15 Y name 3 = -5 Y name 2 = 5 Y name 1 = 15 Letter size = 7...

Customized version of http://www.thingiverse.com/thing:345972 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=345972 Instructions Using the following options: type = 9.6 flat = 0 length = 2 width = 2

... walls that are 2 units thick. It also features a top clearance of 0.2, a lid with thickness of 2 units and an edge thickness of 0.5 units, a bottom that is 2 units thick, and rounded corners with a radius of 5 units. ...The box's width is 40 units.

... created using the Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=29211. ...For instructions, set gridY to 67, gridX to 40, thickness to 2.5, meshSpace to 2.5, meshSolid to 1, and add borders of 3 units in both the Y and X axes.