craftsman battery holder 3d models

Craftsman 20 Volt battery holder, Battery can be placed from either end, Same design both ends, can be installed either way.

It works with my 2 Ah (29141, 40V DC 73Wh { http://www.craftsman.com/craftsman-40v-lithium-ion-battery/p-07198740000P }) and my 4 Ah (138.98742, 40V DC 146Wh { http://www.sears.com/craftsman-40v-rechargeable-lithium-ion-battery-98742/p-07198742000P...

It works with my 2 Ah (29141, 40V DC 73Wh { http://www.craftsman.com/craftsman-40v-lithium-ion-battery/p-07198740000P }) and my 4 Ah (138.98742, 40V DC 146Wh { http://www.sears.com/craftsman-40v-rechargeable-lithium-ion-battery-98742/p-07198742000P...

Battery wall holder for Craftsman 20v batteries. This is a nice and convenient way to keep your batteries ready and accessible for when you need them. I use 1/4" bolts that are 3/4" long to install on my slat wall but I have included a file without...

Craftsmans 20V Battery Holder Mount

Battery holder for 19.2 Craftsman batteries

Remix of https://www.thingiverse.com/thing:4728728 which is for a slightly different battery style. ... Battery Holder for a Craftsman 20V CMCB202 Battery. Designed for offset locating tabs and a wider tool slide than the original design. ...

I have many craftsman Nextec tools that use the same 12V Lithium Ion battery. My goal here is to make an adapter that'll allow me to use these batteries on many other projects around the house, like my son's RC Cars. ToDo: -Rev 13 is a VERY tight...

HOLDS SINGLE NEXTEC 12V BATTERY WITH LOCK PROVISION

Craftsman v2.0 tool and battery holder.

Battery Holder Mount for Craftsman 19.2V with dual mounting points.

I opened the 12V craftsman battery, and removed the battery cells inside, and wired a XT60 connector where I can plug one of 4 cell LiPo battery (it should be a 3 cell for 12V equivalent, but don't have a 3 cell one) I used a 4 cell, 4000 mAh...

I opened the 12V craftsman battery, and removed the battery cells inside, and wired a XT60 connector where I can plug one of 4 cell LiPo battery (it should be a 3 cell for 12V equivalent, but don't have a 3 cell one) I used a 4 cell, 4000 mAh...

This is a wall/under shelf battery holder mount for the matching craftsman batteries. I have mounts for all my other (dewalt) batteries and wanted the same for my craftsman batteries. I believe there are a few lines this may work with, but I...

These are battery mounts I designed for the newer Craftsman V20 line of batteries. There are versions for both horizontal and vertical mounting. ...It is a little tight at first, but after about the first half hour of being used it forms to the battery...

This is a wall/under shelf battery holder mount for the matching craftsman batteries. I have mounts for all my other (dewalt) batteries and wanted the same for my craftsman batteries. I believe there are a few lines this may work with, but I...

I am uploading this as is to share the geometry of the battery in case anymore else is doing something similar or just need it. Please comment or link if you do. I would like to see what you did. Currently the file is only 53mm long for test fitting,...

I could not find a Craftsman 20v battery mount ... so I made one ... actually I made two. Print upright with supports. Print time is around 2 hours for the v2 . Lowpro take about 1.5 hours and has my branding on it :P Oh, use the flattest head...

This is a battery adapter for a Craftsman V20 Battery. I was inspired by Griffin175's battery adapter (https://www.thingiverse.com/thing:3127879). I designed this adapter to not use any hardware to hold the contacts in place or the need to use...

I decide that the best thing to do was get them somewhere centralized and create some kind of holder / mount for them. this is what I came up with. Print Settings Printer: Monoprice 3D ...

Just a very simple yet effective wall mount for the v20 batteries. ...It is sturdy enough for the larger batteries as well. ...Screw is offset due to the grooves in the battery.

Simple replacement battery cover for this great low cost little meter sporting AC and DC current measurement from that clamp.

Craftsman 20v Bit Holder designed to hold 6 standard hex bits for convenience. Has mounting hole to attach to Craftsman 20v Drill/Drivers using the 3mm preinstalled nut. You will need to purchase a 3mm x 16mm screw to secure this to your drill.

Bracket that can be mounted to hold Craftsman V20 tools

This is a small piece that keeps the craftsman screwdrivers in one place with friction

I made a tool holder for Craftsman V20 series tools. I have been using prints from this design (https://www.thingiverse.com/thing:4728728) but thought I'd try something with a little bevel to it and make insertion easier. I print these on the long...

I needed a solution to hang my craftsman tools up out of the way. ...They came with a built in hanger but nothing to hang them on.This attaches easily to the wall and holds my tools with the hooks they cam with.</p>

http://www.thingiverse.com/apps/customizer/run?thing_id=537516 Instructions Using the following options: holder_height = 18 holder_x_size = 65 wall_thickness = 2.4 holder_x_count = 1 holder_y_size = 80 holder_cutout_side = 0.0 holder_angle = 0.0...

You need to harvest the following from an old Craftsman battery: - The battery top - The electrical contact assy - The release buttons - The button springs - The 5 assy screws. For the electrical contacts use Ryobi Contact Plate holder 300001044 or...

Wire spool holder for early 90s Craftsman MIG welder.