craftsman socket rack 3d models

Craftsman socket wrench organizer

I used to have craftsman's socket organizer but it took the whole drawer just to hold the sockets. I condensed the layout so that the ratchets, extensions, and other parts would fit too. Now it all only takes up about 2/3 of the drawer. I printed...

This is a socket organizer for a Craftsman Socket set and sits in the top chest of a craftsman rollaway. Some notes: 1) If you can use 12mm material so the sockets don't fall over, if you can't cut 12mm material, just glue 6mm material on the...

I have a large set of Craftsman sockets (308 piece set #35831). I wanted holders to keep them from rolling around in my tool box. Each of the trays were fit to my sockets, so hopefully the manufactured diameter is consistent and will fit yours...

These should work for craftsman socket sets. I will slowly be updating this as I make/print my way through my toolbox. I was inspired by steve1973's socket organization set but my set didn't match up to his completely. I was able to use some items so...

I loved the Socket Orgainzer by WoodmanXI, but my Craftsman socket set was quite a bit different than that one and I needed to customize to hold all of the sockets in my particular set. I ended up having to build the 3d models again, since I'm not...

Final Metric Deep 375 holds: 9mm, 10mm, 11mm, 12mm, 13mm, 14mm, 15mm, 16mm, 17mm, 18mm, 19mm, 22mm sockets. Metric Short 125 holds: 4mm, 5mm, 5.5mm, 6mm, 7mm, 8mm, 9mm, 10mm, 11mm, 12mm, 13mm, 14mm sockets. ... Long Metric .250 holds: 4mm, 5mm, 6mm,...

Craftsman chisel wall organizer For these chisels: https://amzn.to/3O28yEA

A socket holder made for CRAFTSMAN 12-Piece Metric 1/2-in Drive Set 6-Point Impact Socket Set. (Item #1049272Model #CMMT15887). It holds every socket except for the 27. Printed on the ender 3 so the bed didn't have enough room to nicely put the 27...

This is a single Solidworks model with a design table that has configurations for the following 5 Craftsman Socket Adapters. A zip with a step file of each configuration is also available. 4256 - Adapter 3/8 F to 1/4 M 4257 - Adapter 1/4 F to 3/8 M...

metric socket tray 4-11. ...&nbsp;I paused on a layer to change out the filament for the text.</p>

Craftsman 10'' Table Saw (Model # 315218060) Gear Rack - Part # 0134010228 #88 https://www.searspartsdirect.com/model/319si7aknn-000247/craftsman-315218060-table-saw-parts

Wrench holder for 20 Craftsman Wrenches. ... This on is angled so the largest wrench is in front.

A holder for Craftsman 3/8 drive SAE hex sockets. I took the diameter of the each socket, rounded it up and then added 1mm to try and accept as many other brands as possible. Credit to user OmniMaker for taking care of the heavylifting with his full...

These socket holders will fit the Craftsman XL 1/2" drive sockets. The sockets used to be sold in sets, but now appear to only be for sale individually. SAE: 1-1/16", 1-1/8", 1-3/16", 1-1/4", 1-1/2" Metric: 27mm, 28mm, 29mm, 30mm, 32mm, 36mm...

&nbsp;Specifics for this print:Manufacturer: CraftsmanDrive size 3/8"Size units: SAEIn this group there are a small tray for the few 8-point sockets ever made by Craftsman, and a laydown tray for the small set of SAE deep sockets that includes the...

Organizing my tool box I didn't find a holder on here for the Torx (Star Bit) socket set. This is for the Craftsman 7 bit set. I printed it with the Prusa slicer and put a couple layers of black at the bottom of the text cut outs then switched...

This is a compact socket organizer for 23 piece Craftsman 3/8-inch drive sockets. See the list of approximate socket dimensions below to see if they match your sockets. The total height of the sockets in the holder is about 69 mm (2-11/16 inches).

&nbsp;Specifics for this print:Manufacturer: CraftsmanDrive size 3/8"Size units: metricNotations for layout type:FW = fixed width (arrange tray segments vertically)VW = variable width (arrange tray segments horizontally)NL = no letteringWL = with...

&nbsp;Specifics for this print:Manufacturer: CraftsmanDrive size: ½"Size units: metricNotations for layout type:FW = fixed width (arrange tray segments vertically)VW = variable width (arrange tray segments horizontally)NL = no letteringWL = with...

&nbsp;Specifics for this print:Manufacturer: CraftsmanDrive size: ½"Size units: SAENotations for layout type:FW = fixed width (arrange tray segments vertically)VW = variable width (arrange tray segments horizontally)NL = no letteringWL = with...

Just a simple socket holder, base diameter of these sockets are all the same, but the spacing needed to gradually get bigger. ...

I had acquired these sockets a long time ago and needed a way to keep them organized. ...I am not even sure if I still have the complete set.

I wanted matching metric and standard socket organizers - same length - and I wanted them to be rectangular instead of the normal triangular shape. I also wanted viewable numbers/letters to see the sizes. ... You can paint the raised letters a...

I updated this model to have more of a snug fit on the sockets to prevent them from falling out as easily, as well as adding radii to corners to prevent the likelihood of shattering if dropped. ...I also added an engraving to the side of the tool holder...

A french cleat rack for a 3 pc. ...Craftsman file set that I bought at Sears.

Socket rack, designed for Facom sockets from 10 to 32mm.

Custom socket to make installing roof rack bolts easier

I designed this mount to hold my Craftsman 3 piece pry bar set vertically on a peg board backing. Printed in black PETG with supports at .2 layer height. ...Each pry bar has a recessed area that the butt of the handle rests in so that they don't slide...

this is a door hinge that mounts to the Craftman 2 shelf 3 foot tall stackable tool chest depth storage rack available at Lowes/Rona, it should also work on the Canadian Tire version. designed in Onshape this is one of the several projects i...