creality 5 plus 3d models

I wanted an LED strip light for my Ender 5 Plus, but all I found was this one for the standard Ender 5: https://www.thingiverse.com/thing:4125317 Front and rear lighting is nice, but it wasn't wide enough for the Plus so I needed something bigger. ...

Dual Gear Extruder: This design was specifically developed for: https://www.amazon.com/WINSINN-Extruder-Creality-Upgraded-Aluminum/dp/B07SY745CF/ref=sr_1_2?dchild=1&keywords=dual+gear+extruder+ender+5&qid=1590272315&sr=8-2 This mount securely...

This is a bracket for the Ender 5 Plus controller case to move the cooling fan from the bottom to the rear of the controller case and cover the fan's old hole. The air will now be pulled in the front sides and exhausted out the back. The bracket...

This mount allows to use the stock extruder of the Ender 5 Plus to be used as direct drive extruder. Installation: 1.) Unscrew the fan chassis, the BL-Touch sensor as well as the hotend 2.) Disassemble the upper two mounting wheels of the...

Hello all, Here's an ajustable webCam support for Ender 5 plus ... or for all printers that has 2020 profil All the parts can be printed without support except for part 7. All the parts are printed mostly on the side edge so that the holes are...

So startete ich Freecad und passte die Vorlage an meine Bedürfnisse an. Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: Yes Supports: Yes Resolution: .2 mm Infill: 15% Filament: Material4Print PETG black Category: 3D Printer...

I created a mounting bracket for the BigTreeTech PiTFT50 screen to fit on an Ender 5 Plus. The design is in 2 parts (plus the retaining clips). Because of the way it's designed, you can still mount the Pi on the back of the display if you wish. ...

This model is designed to fit a Vizio xr6m10 tablet (5.5 x 3.5 x 0.2 inches), but you can easily update the model to work with other phones/tablets by tweaking the [Tinkercad...

When you get your aliexpress linear rails for your Ender 5 plus, you might get install blocks as pictured, luckily I did. Those install blocks are inadequate since they end up putting the X gantry far too high on the top 4020 channel. Drop the rails...

One was for Ender3 and the other was a rough Ender 5 Plus design that needed jesus. This should be usable with the Ender5+ with little to no modifications to your printer. It uses the default hardware. BLTouch mount is about 5mm to the left of the...

This is a remix of the Ender 3 Z-axis endstop to use on the Ender 5-plus. The area that holds the endstop board is basically the same, but enlarged and reshaped slightly to fit the endstop boards I have. It was also changed to use M3 heat set...

This is a housing for the Mini 12864 LCD display to fit inside the Ender 5 Plus chassis without modifications. It bolts on from inside using the original mounting points and screws. You mount the LCD to the back cover first with the M4 screws and...

This is a filament lead in tube (Bowden) end holder for Ender 5 Plus direct extrusion modifications. It is designed to hold the end of the filament lead in tube from the filament break detector to the direct extruder. The filament bracket installs in...

This is a housing for the Mini 12864 LCD display to fit inside the Ender 5 Plus chassis without modifications.It bolts on from inside using the original mounting points and screws.You mount the LCD to the back cover first with the M4 screws and nuts,...

Aluminum LED Channel brackets for the Ender 5/ Plus printers. You will need to print two of each file for all four needed. The brackets do not have holes for the wiring, but 10 seconds and a drill bit will put the hole wherever you want it. ...

Mountings bracket to relocate the stock electronics enclosure on an Ender 5 plus to the rear of the machine outside the frame. This re uses the stock bolts that held the enclosure in the frame and M4 bolts and T nuts to mount the brackets to the rear...

Since uploading my Ender 5 Plus Micro Swiss cable support bracket, I have redesigned a bracket to fit at the end of the X Gantry to mount the cable on to support it away from the metal frame and the wheels on the gantry. You will need to install...

This extend your Ender 5 Plus rubber feets by 35mm. (I need this for my own silent cooling solution, maybe I will show you later). Maybe you like this too to add more airflow to the Z stepper motors. You need 4mm brass inlays, so you can reuse the...

...My design has been put to the test on my Ender 5 Plus printer, which operates seamlessly without any hardware holding it back. To accommodate varying bed thicknesses, users can fine-tune their designs using the scale feature in the slicer software.

I encountered a problem with my Ender 5 Plus in that the front was lower than the back even when everything else was equal. This led to rear adjustments being significantly tighter than the front and became an issue when I switched to solid silicon...

Simple yet effective replacement for your Ender 5 Plus duct fan. Exhaust is directed under a small angle, now featuring rails, so airflow points directly at the nozzle tip. I hope you'll be satisfied with the results. If any issues or tips arise,...

Simple but effective replacement for your Ender 5 Plus duct fan. Exhaust in under small angle (now with rails) so air flow is pointed directly to the tip of the nozzle. Hope you will be happy with the results. In case of any problems or tips do not...

... If you like my Design please give me a like or a make. Thank you Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No Resolution: 0,12 Infill: 99 Filament: CR-3D PLA Gold Category: 3D Printer Parts

If your printer uses the same carriage plate that the ender 5 plus does then this should work for you too. This uses the stock BLtouch mount and you can use the stock 40mm fan but if you want the cooling fan you'll need a 5015 blower (I have not done...

---------------------------------------------- This is an adaptation of my unpublished Ender 5 Duet Mount, modified for the Ender 5 Plus. It utilizes a 40mm fan (recommended: 24v SUNON 4020 or 12v Noctua 4020 via a buck converter) to direct air...

This will help with that. This spacer is long enough that the stock Ender 5 + hotend will not be able to touch the bed when you tighten the z axis, so no fear of it crashing. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't...

I use this on the Ender 5 Plus. This is a larger printer. I Print large and fast. The bigger fans help quite a bit. they not only move more air, they are much more dependable and don't clog as easily. I use a 5015 and a 4020. This system seems easier...

3 changes from the original: 1. ...Remixed to fit the SKR 2 board 2. Combined two formats to allow for mounting the Creality or TH3D Mosfet on the same box 3. ...Added optional zip tie brackets for cable management

This fan shroud is designed to precisely fit an Ender 5 Plus with Spider Hot End using the HBE X Carriage (purchase on eBay). It allows the reuse of the factory fans. It is based on https://www.thingiverse.com/thing:5369808 and uses the plate that...

This is a bracket to relocate the front crossbar of the Ender 5 Plus to get a better view of the build plate. You may locate the crossbar at any height you find suitable for your setup. Also consider printing the End Covers that protects you from...