creality 5 plus 3d models

So, I assume these will work for all Creality printers and probably quite a few more. There are several options depending on how you want to mount your cables, and I think I've covered all the bases. All of them fit with a nice click or snap and...

Better yet, are you trying to install the creality spider all metal hotend and it won't fit in the stock cooling system? Well then this is for you. You can re-use the heatsink fan, but you will need to replace the nozzle fan with the same 40mm...

Extruder mount revision 2 for Ender-5 firmware S1_HW_CR4NS200141C13_SW_V1.0.6_F401_International Edition 21 Mar. 2023____Кріплення екструдера ревізія 2 під прошивку Ender-5 S1_HW_CR4NS200141C13_SW_V1.0.6_F401_International Edition 21 Mar. ...2023

Direct Drive Extruder installed on my Cr10s Pro I made this base to fit my printer with this excellent Orbiter 1.5 extruder. ... With this base you use the same screws as the base to use the stand.

Ender 3/5 printer hotend cover. Works with Microswiss direct drive back plate. Carries 1 axial 4010 hotend cooling fan and 2 4020 radial work piece cooling fan. High temperature part. ...Print using fiberglass Nylon or Carbonfiber Nylon.

... ... It includes 5 M3 holes, allowing you to mount it horizontally, vertically or even two L-shaped Ender 5 rails with two M3x8mm screws and two M3 T-nuts (3D printed ones are working well). ... Printed using PETG but PLA should work as well.

... them enough but it works. I also used PETG but only because I had it on the printer already. PLA should work as well. [1.5" 50 Duro Sorbothane Hemispheres](https://www.amazon.com/gp/product/B00516DL5Y) (not an affiliate link, not my store).

Remix of the cooling fan duct from Hangtight's Titan Aero mount to better fit the Ender 5. The original duct interferes with the frame near y=0, so I added a bend to obtain full y travel. ...Cooling airflow is likely compromised, but I haven't noticed...

Original MKS Gen L adaptor didn't fit for the Ender 5 as the PSU was in the way. Moved the mount holes and.. voilà.. Here you go. ... Rev2: The mount holes are 21mm more to the left to give the board a little more space between the frame edge and the...

I remixed this great ender 5 Bed Supports by merlindrz. ... https://www.thingiverse.com/thing:3373479 This is made to fit 10mm aluminium tube and M3 nuts and bolts The tube is a loose fit I just used supper glue to hold it The M3 nuts are a tight...

... by jsjamboree, but I remixed it, so you can fit two pieces of bowden tubing in the inlet and outlet to reduce friction. ... you can use this with the default ender 5 Z-End switch, which most people have left over after an ABL conversion. ... have fun.

I created a design to enhance and extend the stock spool holder on top of my Ender 5 machine, specifically for use with a direct drive extruder. To assemble this setup, I need two short threaded inserts that fit into 10-32 threads. These inserts are...

The original MKS Gen L adaptor didn't fit for the Ender 5 because the PSU was in the way, so it needed to be modified. To solve this problem, I moved the mount holes and made some adjustments, resulting in a perfect fit. ...The revised version of the...

This is a mount to fit my skr 1.3 into my Cr-10 V3 but should work on any printer with v.2.5.2. Also this comes with a price you must cut a hole in the side of your box to get to sd card and usb slot if needed. ...I will make a 3d printed model to help...

This is a mounting adapter designed specifically for the BigtreeTech SKR 1.3 board, engineered to seamlessly integrate into an Ender 5 case. To access the SD card and USB port, you will need to carefully cut out the side of the enclosure. If you...

This is a mount to fit my skr 1.3 into my Cr-10 V3 but should work on any printer with v.2.5.2. Also this comes with a price you must cut a hole in the side of your box to get to sd card and usb slot if needed. ...I will make a 3d printed model to help...

After I've learned I could use my BTT 5" V1 TFT display with Klipper, I searched for proper cases to mount it in an elegant way to my Sovol SV01. @JVJV did a great job for designing one for the Voron which I adapted. I remixed the „feet” of the...

this adds alot of rigidity to the assembly but is very cantilvered to begin with so idk proceed with caution also you may need to clearance one hole because the wasy it sticks out the back of the ender 5 plate it sticks into the plate v2 will...

Hello, here is a remix from: https://www.thingiverse.com/thing:4668934 I rotated the Orbiter 1.5 + 90 degrees to get the motor weight a little closer to the rail. Maybe it's better because of the vibrations ?! There is now a cable recess in the mount...

The angles are useful if someone wants to mount the electronics box of an Ender 5 at the rear end. This can be used when converting an Ender5 /Pro to the CoreXY Zero G Mercury One Project.The benefits are, your cable/wires are close as posible...

This is a remix of the excellent [Ender 5 Bed Supports](https://www.thingiverse.com/thing:3373479/) by [merlindrz](https://www.thingiverse.com/merlindrz/). It contains the individual parts separately, instead of one big file. This makes it easier to...

The Ender 5 is a capable printer, but one significant limitation that has hindered my quest for high-quality prints, similar to those I achieve on my FFCP, is the more intricate leveling system. True, I have managed to produce good quality prints...

Main changes with regard to the mounting bracket file from athlon789789: - this file is made for M4 brass inserts with an outer diameter of ~5.6mm and a depth of up to ~8.1mm (Remember: The orbiter comes with holes for M3 screws - if you want to...

I made a custom mount so I could shorten my Bowden tube, allowing me to reduce retraction during prints to 5-6mm with PETG and minimize stringing. To replicate this mod, you'll need a stepper motor extension cable and a PTFE Bowden tube kit with M6...

Im Rahmen meines Ender 5 Plus Umbauprojektes, musste ein Adapter für die neue SKR 1.4 Turbo Platine. Der Adapter hat noch eine Halterung für die SD Verlängerung von Creality. Für die Montage werden, 3 M3x8 Senk, 4 M3x16 Zylinder und 4 M3x6...

My printer is a Creality Ender 5 Plus.

For mount Duet Wifi board to Ender 5 Plus.

Audi R8 5.2 FSI quattro Plus 'Liberty Walk' '14

Ender 5 Plus Heated bed cabel holder. ... Support: No

It is an adapter for Duet into Ender 5 PLUS.