creality cr touch 3d models

I recently acquired a CR-10 and was immediately struck by the fan's unique design, featuring 4 indented screw holes that differ from those found on other part cooling fans I've encountered. The part cooling itself is woefully inadequate, resulting in...

This is just a simple CR Touch mount i made for the Creality Ender 7

CR Touch version.

CR Touch version.

Smooth Fang CR Touch Mount

This was modified to attach both the BL Touch and the Creality laser to the Ender 3 Pro.

This is a simple spacer based on the CR-Touch bed leveler but will also work with a BL-Touch. Issue I was having was with changing extruders and nozzles and ending up with the probes being too high thus causing my nozzle to ram into the bed. With...

this is a cr touch braket for sovol sv01

This is Cr Touch bracket for sovol sv01

On my CR-10 V3, if I used the CR Touch as-is it would cause my nozzle to crash into the print-bed. This spacer adds 4mm headroom between the probe and nozzle. Works with the stock screws that come with the CR Touch. I printed with 50% infill,...

Re mixed for a CR Touch, offset -43.1, 0 holes for CR touch are designed for brass inserts

Since the CR touch wants to be mounted under the holder and the BL touch is mounted above it, the stock holder wont work. I decided to make my own. You'll need 4 M3x8 screws and 4 M3 nuts to secure the holder onto the carriage and the CR touch onto...

Here's CR-TOUCH support for ENDER3 V2 printheads. ... Fasteners M3x13 x4

Remixed to fit on my CR-10 with Hemera

this is a modified mount for CR touch for Fang use screws that came with CR touch original https://www.thingiverse.com/thing:4630748 suggest 100% infill and supports

Remix for Satsana by SYJ to fit CR Touch. ...Previous design allowed you to connect a BLT You will need a few extra nuts to lower the Cr Touch to make it functional + adjust your z offset

Realized that the bracket didnt allow room for CR Touch so i chopped a square out to suite my needs

I extended the Klemco left fan by ~3mm so I could use the CR touch instead of a BL touch. I am using the CR touch mount from by JKCTX1. I like having dual fans! ...This has a E3D V6 with a Volcano end.

The BL-Touch mounts that are posted don't work because the CR-Touch is fatter and the cable comes out the top. This works fine with the CR-Touch, and should also work with the BL. ... V2 has the probe more centered -- easier to put together.

https://www.thingiverse.com/thing:2759439This mount is shortened and adjusted to bring the CR Touch closer to the bed compared to the original.The original design did not get my CR Touch close enough to detect the bed, this design should fix that for...

This mount took inspiration from the mount included with the CR-Touch that fits with the Ender3.This model uses the same dimensions as the parent remix, however it was made fresh in Tinkercad...

https://www.thingiverse.com/thing:2759439 This mount is shortened and adjusted to bring the CR Touch closer to the bed compared to the original. The original design did not get my CR Touch close enough to detect the bed, this design should fix that...

I liked the shroud I found by chubbyzook (thing: 4821813). ...So, when it was time for a CR Touch, I remixed this design.

This Bracket is specifically designed for this direct drive. ...print with the open slide slot for the CR Touch wiring on the build plate to save using supports

Ender 3 pro CR/BL touch offset for custom fan ducts, 2 extra screw required. ... NOZZLE_TO_PROBE_OFFSET { -52.5, -13, 0 }

CR Touch sensor mount and spacer. ... The center of the holes are 18mm distant and the holes are 1,5mm of radius (3mm of diameter).

... SealthySwiss doesn't work with CR Touch due to the location of the connector, and has a tendancy to bend even if printed in ABS. ... I clearanced it for the CR Touch connector, added strengthening braces, and tightened the clearance to the fan shroud.

I remixed the Support Touch-mi CR-10 from Thingiverse (https://www.thingiverse.com/thing:3350748) for my own CR-10S printer. ...I made the X-axis cart a bit larger, about 2mm more than usual, and also modified the magnet holder so it doesn't spin...

This mount is for the CR Touch paired with the Spider 3.0 hotend.Z Offset = -2.65 (Your Value may differ, start at 0 offset to be safe)Y Offset = 0.0X Offset = 31.3

<p>I had been using a satsana shroud I found over on thingiverse by chubbyzook (Thing: 4821813). ...I couldn't find one with the propper CR Touch mount, so I remixed the one I was already using.Print with supports touching buildplate