Creality CR10-Max fixed fanduct-shroud
Creality CR10-Max fixed fanduct-shroud
thingiverse

This is derived from one of the highest quality models, but it's not deep enough for the fan on the CR10 Max. ...I adjusted it in Blender 3D, also gave the screw holes a bit more meat, and opened up the duct for better downward airflow I also laid...

Creality CR10 Max Fan cover
Creality CR10 Max Fan cover
thingiverse

This is a remix because it wasn't fit in mine

Creality CR10 MAX CR10-S PRO Fan Duct Cooling OEM Refined
Creality CR10 MAX CR10-S PRO Fan Duct Cooling OEM Refined
thingiverse

I realized after printing Gwiens version there was a 3mm+ gap from my original OEM fan from my Creality CR10 MAX which would not fit. Not sure if the manufacturer updated thier OEM fan... However with some mods on CAD and refining some detail this...

Creality CR10 MAX CR10-S PRO Fan Duct Cooling OEM Reinforced
Creality CR10 MAX CR10-S PRO Fan Duct Cooling OEM Reinforced
thingiverse

Upgraded the OEM Fan duct with better mounting points. Air flow remains the same as the original! Best printed with Tree support but also no problem to do without. Use PETG for higher temperature resistance. ...

Creality CR10s Pro & CR10 Max Filament Guide
Creality CR10s Pro & CR10 Max Filament Guide
thingiverse

This is a filament guide for the Creality CR-10s Pro and Max printers. This print uses Skateboard Bearings, they should be the following (or equal specs): https://amzn.to/3a5lMvb These are constructed in a way so they do not need any support.

Creality CR10s Pro & CR10 Max Filament Guide
Creality CR10s Pro & CR10 Max Filament Guide
prusaprinters

This is a filament guide for the Creality CR-10s Pro and Max printers. This print uses Skateboard Bearings, they should be the following (or equal specs): https://amzn.to/3a5lMvb These are constructed in a way so they do not need any support. Enjoy!...

Upgrade cr10 max max
Upgrade cr10 max max
cults3d

Allows you to switch to direct drive mode with your Creality CR10 MAX printer

CR10-MAX Direct Extruder
CR10-MAX Direct Extruder
myminifactory

CR10-MAX Direct Extruder

PLA Guide CR10 Max
PLA Guide CR10 Max
thingiverse

PLA filament Guide CR10 Max

CR10 Max PTFE Support
CR10 Max PTFE Support
thingiverse

PTFE / Cable support for CR10 Max.

CR10 Hotend pro max
CR10 Hotend pro max
grabcad

This is the new PRO MAX hotend of CR10

CR10 Max hard stop
CR10 Max hard stop
thingiverse

This is a hard stop for the Creality CR-10 Max Y axis. The hard stop is attached to the inner part of the opposite rail where the limit switch is mounted. 3 M5x25mm screws and 3 slot nuts are required to hold it in place. ...This will protect the...

Fan Duct - CR10 Max / CR10 Pro V2
Fan Duct - CR10 Max / CR10 Pro V2
thingiverse

Based very loosely (ie inspiration) on the Cr10 Pro fan duct by Plasma https://www.thingiverse.com/thing:4391624, which I had been using for some time however it didnt print well in abs. This was a ground up design from scratch in Fusion 360. ...

CR10 Max ribbon cable holder
CR10 Max ribbon cable holder
thingiverse

Cable holders for aligning the ribbon cable for the CR10 Max. One end attaches to the lower V slot in the base profile and the other one is secured with an M4 bolt and a T-nut. ...For best results captive M4 slot nuts are recommended.

CR10 Max Filament detector upgrade
CR10 Max Filament detector upgrade
thingiverse

Might be similar for other CR10 printers but I only have Max version so I do not know for sure. Creality firmware doesn't let you properly handle the switch. Tiny Machines firmware is much better, but still gives issues. On standard CR10 Max...

CR10 Max Filament Roller Guide
CR10 Max Filament Roller Guide
myminifactory

Got a CR10 Max the other day, and noticed that the filament shreds a bit as it runs into the filament sensor. I used a Fidgit Spinner bearing, since they are plentiful. It takes a bit of pressure to get the bearing on, but apply evenly.To avoid wear,...

CR10 Max Filament Arm Roller
CR10 Max Filament Arm Roller
thingiverse

Got a CR10 Max the other day, and noticed that the filament shreds a bit as it runs into the filament sensor. I used a Fidgit Spinner bearing, since they are plentiful. It takes a bit of pressure to get the bearing on, but apply evenly. Keeping...

CR10 Max Direct drive extruder
CR10 Max Direct drive extruder
thingiverse

I think this is for a later version of the CR10 max then the original version on here, thanks to elik745i for the initial design. Modified space for extruder arm, moved filament detector back 1.5mm, moved hole for compression bolt as it was 3mm...

CR10 Max+BL - Nova Mount
CR10 Max+BL - Nova Mount
thingiverse

Created a mount plate for CR10 Max, made accommodations for BL Touch and utilized Tevo 5020 blower mount bracket (part cooling). I needed to make this due to Tevo CR10s mount not allowing the Nova hotend to reach the bed without crashing the gantry...

typo creality cr10
typo creality cr10
cults3d

Typo creality cr10

typo creality cr10
typo creality cr10
thingiverse

Typo creality cr10

Creality cr10 case
Creality cr10 case
grabcad

a case for the cr10 s5. ...can be printed on your own printer s5!

Creality CR10 Spool adapter
Creality CR10 Spool adapter
thingiverse

Simple adapter for original Creality CR10 spool mount. Check the diameter of your spool and compare it with model inner and outer diameter. ... My filament spool inner diameter is 52mm and stock cr10 outer diameter is 30mm.

Creality CR10 Fuse Holder
Creality CR10 Fuse Holder
thingiverse

Needed a fuse holder for my CR10 so I remixed one already on here for what appears to be an ANET to make it fit.

Creality CR10 Vibration Stand
Creality CR10 Vibration Stand
thingiverse

Vibration stand for the CR10, print a set of two and put one in front and one in back of the controller box to lesson the effects of vibration on the controller and reel assembly.

Filamentrollenhalter Creality CR10 V2
Filamentrollenhalter Creality CR10 V2
thingiverse

Here is a filament spool holder to fit on an cr10 v2 case. ... In combination with the short screw from that thing https://www.thingiverse.com/thing:1241566 With an M8 or 8mm axle.

Creality CR10 Desk Bracket
Creality CR10 Desk Bracket
thingiverse

The CR10 takes up a lot of room on the desk, So these enable you to hang the control unit to the left of the printer. ... Use double sided foam tape or velcro on the base to stop it from sliding back when pressing the control knob.

Creality Cr10 Cooling Head
Creality Cr10 Cooling Head
thingiverse

The original Hotend Cooling of an Creality Cr10 does not have the optimal cooling properties. In addition, the weight of the Alucovers is not the best solution for vibration damping and also very top-heavy. That's why I designed this all-in-one...

Creality CR10 Bumper (front)
Creality CR10 Bumper (front)
prusaprinters

My CR10 is standing on a shelf, next to my kitchendoor, and the front / builtplate stands beyond the edge, so I am constantly afraid of running into it. It also prevents you from standing too close to the printer, when you are mesmerized watchint the...

Creality CR10 hotend fix
Creality CR10 hotend fix
thingiverse

Creality stock hotend upgrade - Simple and effective - Fixes problem with extruding and clogging - Using bowden PTFE tube and printed parts, no need of extra hardware - Fast print Upgrade is made for my Ender 3 and Ender 3 Pro, but it works with all...