creality ender 3 filament 3d models

This is Creality 3D printer - miniature, home decoration

... connected it to the USB hub. I attempted to print it on my Ender 3 but ended up printing on my Elegoo Mars because I was unable to achieve the right clearance fit on the Ender 3. ... Currently, my Wyze Cam is plugged in and functioning flawlessly.

Creality Ender alignment prints for digital gauge. These are the Companion models to this video: https://youtu.be/AN0MlQMMew0 Given that the models are structural yet not specifically load-bearing, I printed the gauge holder in Cura with 0.32mm...

Tool holder for Ender 3 stock tool - no extra screw required. Small tool in front, large one behind. Cutting pliers and other tools are securely held due to a height of 20mm. This measurement matches the horizontal profile exactly. ... The tool holder...

I made some modifications to be able to adapt it to the ender 3 pro and v2 or other bed with the same chassis. ... I strongly advise to print the model with a resin printer,the model requires a lot of details in the teeth.

This is a simple solution to the black hole over the micro sd card slot in the ender 3. If the card has been swallowed multiple times by the machine. ... It's enough to print it and insert it into the location above the SD card.

...... I conceived a fundamental Power Supply Cover for the Ender 3, which also muffles the PS-FAN and redirects hot air upwards. ... Note: The inner wall is excessively high and thin, causing it to wobble during printing, so I simply chopped it off after.

On Creality printers (at least the Ender 3), the cooling fan in the electronics is coupled with the part-cooling fan, so make sure to turn that on (M106 S255) to avoid overheating your printer electronics while plotting. You may or may not include...

... screws on top of the main electronics cover. Once all obstacles were cleared, I could slip the final foot into its designated slot within the aluminum frame. The entire printing process took less than two hours to complete on my Ender 3 printer.

______________________________________________________________________ This is a remix of the handle included in this Thingiverse item: Ender 3 bed handle with removable Raspberry Pi camera mount by PatriceLoco -...

While making my first prints on the Ender-3 V2 the cable that runs to the nozzle got stuck between the printbed and the motor that is situated in the rear of the printer. To prevent this from happening I designed this cable holder. The cable...

I install a BLtouch sensor directly inside the fan shroud on my stock Ender 3 or CR-10 to get it as close as possible to the nozzle. My part cooling duct is designed specifically to accept a Sunon 5020 GB1205PKV3-8AY Maglev blower fan, ensuring...

There's a version labeled "Creality" and one that isn't. ...It might work for other Creality Printers as well. The design doesn't look great with Smurf-Blue PLA, but my black PLA was all out. ...I'd love to see your prints in another color, though!

**Other Ender 3 Parts.** [Tusk Fan Shroud](https://www.thingiverse.com/thing:3055926) [Z Endstop Bracket](https://www.thingiverse.com/thing:3057136) [Y Endstop Bracket](https://www.thingiverse.com/thing:3057132) [Cable...

This is a compact cooling vent for the standard fan that comes with the Ender 3 printer. To install it, simply swap out the original fan duct with this one. For optimal results, print it from PETG due to its proximity to the hot end, but...

Hello all, here is my update to the Ender 3 Printer external housing. If you want to rebuild this, you need basic knowledge in soldering and electrical engineering. The following things are needed for the external housing: - 120 MM PC fan +...

https://www.thingiverse.com/thing:3639454** I stumbled upon Filboyt's Ender 3 vent ring creation and was impressed, so I decided to print it out. It fit perfectly with my printer, and the 'bowl of water test' confirmed its excellent performance. So...

A new designed knob to feed the extruder easily with new filament.

Users gain access to utilizing filament spools featuring a reduced central aperture diameter.

You must print the piece labelled ‘cable chain - link’ 15 timesI will release a video of how to install it in a week or two whenever i can.Unfortunately this doesn't work for the Ender 3 v2. This has been designed for printers that have been...

Unfortunately this doesn't work for the Ender 3 v2. This has been designed for printers that have been converted to direct drive or do not have their extruder in the same place. The only extra hardware you will need is one M6x20 bolt with a nut, it...

I am designing a new case for my Ender's power supply, electronics and screens, so I am recreating each part in Fusion 360. Thought I would share for your designs. ... If you can print this into a working model I will be highly impressed.

... crossbar of the printer. ...A PTFE tube coupling with a diameter of 9 mm is screwed into the top. At the bottom, the filament can be pulled through a funnel shape in any direction. ... The sensor can be screwed on directly with the original screws.

... of bracket to mount the hardbody to. Important Note! This filement spool holder only works for small filament rolls with a maximum width of 55mm (2.165 inches.) The diameter of the filaments center hole should not extend over 17,5mm (0.69 inches.)

When I bought a 'special' filament it came in a spool that didn't fit in the printer holder, so I designed one that takes advantage of the same nut. ...Although visually that part is not very aesthetic, it is hidden by the nut :) To the STL file I...

If you use PETG filament, fill can be 50%; with 80% PLA one side broke (with 3mm thickness) but I glued it with Super Glue and it turned out fine. However, I have redesigned and increased to 4mm thick, it feels much more solid and infill can go to...

Printed at one time New Creality Slicer => standard quality Ender 6, Creality, filament spool holder, spool holder, to save space

For those wondering how I got this old camera working with my Raspberry Pi 3, rest assured it was a breeze - just plug in the USB cable and enable the camera settings in config. ...The fact that this is an older model (5-7 years old) made no difference...

This is a filament runout sensor with a roller that uses the stock z-stop switch of the Ender series printers (you don't need it if you have updated to bl touch). It does not need any additional parts and is 100% 3D printable. You will need: -...

Ender 3 filament roller