creality ender 3 pro filament sensor 3d models

Ender 3 - Spool Holder Adapter for DD + Filament sensor adapter

***For Creality Ender 3/Pro/V2 Printers Converted to Direct Drive Only*** Converted my Ender 3 V2 to direct drive and needed a place to mount my BigTreeTech (BTT) Smart Filament Sensor. The mounts I found were located in a place that would restrict...

Adapter to use the Creality runout sensor on the Ender 5 plus with a direct drive setup with a bowden tube from the sensor to the extruder. ...uses stock hardware and has four mounting holes for options on where you want to mount it to your printer.

this was my first 3D printing <3 ) So, here is my remixed version of the filament guide, with a small pulley to make the arrival of the filament a little more fluid, as well as an entry designed to slide the filament in or out very quickly if...

this was my first 3D printing <3 ) So, here is my remixed version of the filament guide, with a small pulley to make the arrival of the filament a little more fluid, as well as an entry designed to slide the filament in or out very quickly if...

COMPLETE SUPPORT FOR ENDER3 CABLES, + GUIDE BEARING + DUST SHIELD + SWITCH SENSOR TO BE ATTACHED BETWEEN 24V POWER FEED AND THE BOARD, TO OPTIMIZE THE POWER-Loss / RESTART FUNCTION, WE ENCOURAGE CHANGES AND SUGGESTIONS.

... This is a mix of two dust filter ideas: https://www.printables.com/model/262818-filament-dust-filter-for-ender-2-pro https://www.thingiverse.com/thing:190118 Print Settings Printer: Ender 2 Pro Rafts: No Supports: No Resolution: 0.1 mm Infill: 100%

Remix of filament holder to use stock nut. ...https://www.thingiverse.com/thing:3209211

Allows to put filament spool aside the printer. ... End of filament need to be bend a bit to go freely behind extruder gear (this is not this guide issue).

#### Changes - Rotated the holder 35° to work better with this filament spool holder mount: https://www.thingiverse.com/thing:5397466

BigTreeTech Smart Filament Sensor Module (https://github.com/bigtreetech/smart-filament-detection-module) Holder for: * Ender-3 * Ender-3 Pro * Ender-3 v2 Variants: * for Stock Extruder * for BMG Extruder Notes: * 2 pieces of M3x10 screws were used...

BigTreeTech Smart Filament Sensor Module (https://github.com/bigtreetech/smart-filament-detection-module) Holder for: * Ender-3 * Ender-3 Pro * Ender-3 v2 Variants: * for Stock Extruder * for BMG Extruder Notes: * 2 pieces of M3x10 screws were used...

You can print the entire Filament Guide using your 3D printer or upgrade it by swapping out the filament wheels for the linked bearings found at https://www.amazon.com/gp/product/B07MY2LWNV/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1. ... This...

... filament spool is flat. ...But if the filament spool has ribs, it might get caught and while it seems it just gets turned around, i think that is just asking for trouble. ...So i made a version with guides at the ends that lift the booms over the ribs.

By integrating a filament guide extension, I've managed to merge the functionality of a Z bearing holder and filament guide into a single component. ...I'm pleased with how this solution is working out for me - you might want to give it a try as well!

(2) Keeping the assembly in the same orientation, attach your filament spool (upside down) with the screws. Alternatively, put something in the hole, like a thin allen wrench or the pointy part of a fingernail clipper, to hold the T nut in place. ...

... time was only 7 minutes, making it a quick and efficient process. Since I chose to use PLA for this project, I'm pleased with its performance - it rolls freely around the lead screw with minimal friction on both the filament and the screw itself.

I love the original filament guide this is based on, but when I added a dual Z-Axis kit, I couldn't use it anymore. ... So, I created this remix that mounts the arm on the front side of the 2020 extrusion and still places the guide loop in nearly the...

I wanted the filament spool to be 90 Degree turned to the left side of the printer. So i designed this conversion kit and redesigned the Spool Holder itself. With the redesign you can print everything at once WITHOUT USING SUPPORTS! Just place the...

So the original file was everything I needed it to be: an extruder piece that constrains the filament path more than the stock one, and uses one of the nine spare PC4-M10 couplings I had left over from the 10 pack I bought to replace the one that...

E3D Hemera mount for Creality CR and Ender 3 / Ender 2 series printers with a mount for a readily available filament runout sensor available from Amazon or AliExpress. Note: The EZOut filament sensor from TH3D Studios will fit the generic sensor...

Petsfang Mount for CR Touch and Sonic Pad G Sensor ADXK345 for Ender 3 Pro using stock hotend plate

The sensor moves along with filament, this will solve problems when you don't have enough space to install my stationary sensor holder found [here](https://www.printables.com/model/544261-creality-filament-sensor-holder") This filament guide is a...

A bracket to mount Creality's runout sensor on your Ender 3 Pro if you've converted it to direct drive extrusion. ... I would have been happy if this part held up long enough for me to make something out of metal, but after a few prints I don't think...

This is sort of a remix of Filament Runout Sensor w/ Creality Limit Switch by 3djpco - Thingiverse and Ender 3 / Pro Filament Runout Sensor using Limit Switch by nandogommez - ThingiverseI used both before but the little spacer that you glue onto the...

Ender 3 runout sensor microswitch case

Remix of Ender 3 Filament Sensor Bracket for Direct Drive to add a V-Slot.

Made this for my Ender 3 V2 to top mount a Creality filament sensor. I used the original creality M3 screws for the filament sensor and then 2 M4 x 16mm screws for the swivel joint. You need to adjust the tension on the 2 screws so it positions it...

... has been modified to be aligned with the entrance of the BMG extruder. If you are interested in the TriangleLab Filament Sensor mount for the stock Ender 3 and Ender 3 Pro please check my other design: https://www.thingiverse.com/thing:4250566

This design uses the original extruder mount as a base mount for a filament runout sensor, consisting of a creality z-stop switch. In my case the switch labeled with "2030". The author of the [original filament...