creality ender 5 plus 3d printer

Remixed to fit the rear 2020 bar on the Ender 5 Plus. ...Slots over the extrusion and bolts down with 2 x M4 bolts and T-nuts.

I have made a set for all sides of the Ender 5 Plus. ... Feel free to tip me to keep up designing stuff for you guys/girls :-)

ender 5 plus direct drive. will probably need an extension for extruder motor. ...i have some spacer for cable support ill share at a later time.

remixed for ender 5 plus with microswiss direct drive kit. notch added to clear belt mounting. ...slightly larger clearance hole for microswiss plate mounting.

Spul holder for Ender 5 Plus, fits with 1kg (max 79mm) 2KG Spuls (max104mm). ... 2x slot nuts and suitable screws are required for fastening.

hello everyone this is a kit for convert your ender 5 plus to drect drive.so you can print tpu filaments with no problem

A cover for the power supply from the ender 5 plus. I recommend customizing it. ...Its perfect if u want to change the power supply fans.

The way I have my Ender 5 Plus set up, a cable sleeve just dangles loosely and frequently scrapes against the printer's frame. This is the first modification I've made to the printer. I printed the part with 40% infill, 100mm/s speed, .2mm layer...

... to increase the sides to 3mm instead of 1.5. I also increased the thickness on the mount for the Ender 5 Plus because I found that the original "wiggled" too much on my printer when mounted. ... I added two additional screws to the block as well.

Inspired by a fantastic video from Tripod in his garage, where he provides an extremely detailed walkthrough of installing Bigtreetech's SKR 1.4 into an Ender 5 Plus, based on KAY3D's Cheetah 5.0 Marlin Firmware. Since I had acquired several SKR 1.4...

This will help with that. This spacer is long enough that the stock Ender 5 + hotend will not be able to touch the bed when you tighten the z axis, so no fear of it crashing. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't...

Introducing my alternative solution for upgrading the hotend of the Ender 5 Plus, incorporating the Spider Hotend from Creality along with dual 40x40x10 fans.This upgraded version boasts dual fans, an additional fixation point at the rear,...

My solution to using the Creality Spider on my Ender 5 Plus... I used the E3D Volcano mount to attach the Spider to the Ender 5 Plus. This allows you to position the Spider at the same z height as the stock hotend. You mount it upside down from the...

Modified based on https://www.thingiverse.com/thing:4795205 for the Ender-5 Plus * Changes some of the screw points * Moved one of them to allow for a Ground Wire * Added clamp system for the Ender-5 Plus control box All credit goes to the original...

... If you like my Design please give me a like or a make. Thank you Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No Resolution: 0,12 Infill: 99 Filament: CR-3D PLA Gold Category: 3D Printer Parts

This is my version of LED strip support for ENDER 5 PLUS. Is to be print with support , back on print plate. there is a left, and right part, but they are quiet similar, so maybe no matter if you print only one piece twice. You will need : 16...

This is a magnetic snap-on case for the BTT TFT24 display to attach to a Ender-5 Plus printer equipped with a BTT SKR v1.3 or v1.4 board. Four magnets are holding the case onto the existing LCD cutout. Magnets: 4 pcs 10mm diameter and 2mm...

... stop. ...I was having issues printing on the 5 plus and discovered that the PLASTIC corner braces were cracked. I replaced them all with machined aluminum and the printer is now very rigid. ...I made a remix of the ender 3 bracket for the limit stop.

This is a housing for the Mini 12864 LCD display to fit inside the Ender 5 Plus chassis without modifications. It bolts on from inside using the original mounting points and screws. You mount the LCD to the back cover first with the M4 screws and...

This is a housing for the Mini 12864 LCD display to fit inside the Ender 5 Plus chassis without modifications.It bolts on from inside using the original mounting points and screws.You mount the LCD to the back cover first with the M4 screws and nuts,...

Ersatzteil für meinen Ender 5 Plus, da der Eckwinkel / Eckverbinder gebrochen war. ... Winkellänge 35mm

One was for Ender3 and the other was a rough Ender 5 Plus design that needed jesus. This should be usable with the Ender5+ with little to no modifications to your printer. It uses the default hardware. ...BLTouch mount is about 5mm to the left of the...

Heated bed control block found inside the Ender 5 Plus. ...Does not include all components, and the heat sink isn't visually accurate (but the external dimensions are correct)

I took GenMatthius' innovative Dial Indicator Holder design and adapted it to perfectly fit the Ender 5 Plus fan housing, capitalizing on its versatility to deliver a customized solution for the community.

If you have an Ender 5 Plus with a Wham Bam bed, you can use this stl file and image to set it up in Prusa Slicer. Print instructionsNo printing required

Couvercle Magnétique pour Ender 5 Plus. Fini les mouches, moucherons, moustiques attirés la nuit par l'éclairage de l'écran. Une couvercle simple et efficace. Nécessite 4 aimants de 12x1mm... ...et un peu de colle.

Remixed an ender 5 plus fan duct to fit on my fan. ...The previous one had some extra plastic on that the screws go through and didn't fit on mine.

Ender 5 Plus Z-axis supports. Has slots (for flexibility) for M5 screws with a counter-bore for flush mounting. ... The bearing used is a 608, in this case a ZZ as I had them already.

Heated bed control block found inside the Ender 5 Plus. ...Does not include all components, and the heat sink isn't visually accurate (but the external dimensions are correct)

Adapter bracket for an SKR 2. ... Made for Ender 5 Plus, could fit others. I used a SKR 2 but should fit 1.4, 1.3 also. ... Has wire tie down points at the bottom.