creality ender models

You Will Need: * Print 1: "Dual Bearing Filament Guide Ender 3" * Print 2: "Bearing Pin 4.0mm" * Buy 2: U604ZZ Ball Bearings (eBay, Amazon, etc.) Printing Tips: * Print the main part with the mounting slot facing down. * Print the pins with the...

I decided to upgrade my Creality CR-10 printer and stumbled upon this awesome laser head that can easily be attached to this printer. Four small neodymium magnets on the laser head make it easy to secure it to the metal extruder shroud. I wasn't...

The cooling duct is based on the "Stock Creality Sprite Fan Double Duct" from Sorkin and adapt it to fit a blower fan 5020 24VDC on it. It is super quiet and really effective. The Hotend duct is a creation of me, I wanted to keep the BLTouch...

So, I assume these will work for all Creality printers and probably quite a few more. There are several options depending on how you want to mount your cables, and I think I've covered all the bases. All of them fit with a nice click or snap and...

This Thing was inspired by: https://www.thingiverse.com/thing:2502886 (Thanks for the best Upgrade-Idea for the Ender-2) The Firmware is on this thing as .zip for download available. I make some Customs in Firmware: 1. used original TFT-Firmware...

Dial Indicator Holder used to mount a dial indicator purchased at Harbor Freight onto the head of the extruder on Ender 3 Neo v2 printer. It is shaped on the inside to copy the contour of the head. I installed 2 nylon screws on the top in order to...

Remixed the "Ender 3 Filament Sensor and guide" by rghawi in order to add some chamfer to the piece so that these sensors (see below for link) would fit. ...Previously, the sensor was so big that the button was pressed with it in the sensor guide (need...

I utilized the hotend cooler for my Ender 3, but I couldn't conceal the cables neatly. This is a remix to provide some space for cable management enthusiasts. The cable from the dual fans is secured by a tie-rip on top. The cable from the hotend fan...

I made an enclosure for my Ender 3 S1 Pro and wanted to put the controller outside for easy manual control... (I might build an Octoprint RPi enclosure with switching relays etc at some point as one larger unit integrating the touch control...). ...

This is a remix of the excellent [Ender 5 Bed Supports](https://www.thingiverse.com/thing:3373479/) by [merlindrz](https://www.thingiverse.com/merlindrz/). It contains the individual parts separately, instead of one big file. This makes it easier to...

I have printed from Spectrum CF-Nylon PA6 on my Ender 3 because I love this material. You can print from PETG/ABS/ASA. I would skip PLA due to low thermal resistance. I have Micro Swiss clone hotend with original E3D NozzleX. ... Board is SKR Mini...

The angles are useful if someone wants to mount the electronics box of an Ender 5 at the rear end. This can be used when converting an Ender5 /Pro to the CoreXY Zero G Mercury One Project.The benefits are, your cable/wires are close as posible...

Stock Y axis on Ender 3 has problems, soft aluminum plate makes wheel alignment challenging. Wheel spacers dig in, causing wheels to bow. Even when wheels work well, I still don't like them for Y beds. This fix addresses that. Re-used existing bed...

You must drill an little hole in the orginial case from your Ender 3V2 for the powercable of your PI. Update 08.02.2022: Today I test my desgined Remixed with my PI4 and I get some issues. I add an Hole vor the Powercable in the drawer wall...

I've tailored my Cura Profile specifically for the Ender 3 to successfully print the wings of the Northern Pike 3D printed airplane. Since the one listed in the original couldn't be loaded on Cura 4.4, I invested time crafting my own custom setup. To...

... in Cura using CHEP's 4.8 rough profile, with my own calibrated flow rate. I used supports for the hollow Neopixel slot, not touching the bed. You may not need them. # Hardware used Ender 3 Pro SKR Mini E3 V2.0 Adafruit Neopixel Stick 3DQF PLA

Tested on Ender 3 and Lotmaxx SC-10, but should work on most printers using 2020 extrusion for the X-axis. Parts needed: 1x Cerality style endstop 2x M3x5 bolts (to attach the endstop to bracket) 2x M3 T-nuts 2x M3x10 bolts (to attach the bracket...

So I thought about a light shade for the Ender 3 S1 Pro and searched for it on Thingiverse. But what I found wasn't satisfactory to me. That's why I designed one from scratch. :-) Instead of many others, this design is different in some ways: ...

I experimented with multiple blower attachments for my Ender 5 ([currently](https://www.thingiverse.com/thing:3855884) ), but one thing I consistently observed was that once the duct became more complex than the original design, I encountered back...

This is a Direct drive mount compatible with the ender 3 style carriages that uses the Slice engineering copperhead with the LGX lite The design is available in three options for the hotend: -rigid mounted copperhead (files without specific hotend...

**Important Note**: I'm currently using the following printhead on my Ender 4: https://www.thingiverse.com/thing:2836195. Keep in mind that this means I can't confirm whether the original printhead or alternative options with my modification will...

... 24V to 5V DC buck converter). * Added companion bottom plate for increased air flow. (Remixed from [Ender 3 V2 Mainboard Cover Reinforced](https://www.thingiverse.com/thing:5174835) by [DreamX_MV](https://www.thingiverse.com/DreamX_MV))

... 3.) This version is best printed with support material. I recommend using the "Tree support" method for optimal results. 4.) In this iteration, the original extinguishers of the Ender 3 are still utilized to maintain consistency and reliability.

... not tested this remix yet. check the files before you print it. post your prints and provide feedback on the design. must have a meanwell LRS-350-24 from the ender pro to use schaffner 281-10-06 or schaffner 281-6-06. ...LRS-350-24 is 30mm thick.

This is the replacement to the Ender 3 Stock Fan mount. It's definitely not the Fang.\r\nWith the Side fan vent, identical airflow as Stock can be maintained with ease. ...The nozzle remains clearly visible for low-height prints and timelapse...

I remixed the Drill Guide for my Ender 3 Y Axis Plate, which is the newer non-pro version. Thanks to bobblejot for the awesome original design. Visit bobblejot's original design for the other parts of this mod. **Update: January 10, 2019** I added...

This modification is based on the Github stp file here https://github.com/Creality3DPrinting/Ender-3/tree/master/Ender-3%20Mechanical/STP for the extruder idler arm, allowing it to function without threading and using only stock screws. The option...

1 Creality end stop switch / runout switch 2 M3 nuts 2 M3 x 16 cap head screws 1 5 mm diameter ball bearing 2 small pieces of Bowden tubing 1 608 bearing or 625 bearing 1 M4 x 16 cap head screw 1 M4 nut 2 printed spacers Insert the ball bearing into...

29\09\20 There is a newer version of this thing here: https://www.thingiverse.com/thing:4609997 Edit 17\08\20: Just to confirm this will fit the Ender 3 V2 as well yet please note the V2 firmware does not appear to provide any refresh options in the...

29\09\20 There is a newer version of this thing here: https://www.thingiverse.com/thing:4609997 Edit 17\08\20: Just to confirm this will fit the Ender 3 V2 as well yet please note the V2 firmware does not appear to provide any refresh options in the...