creality filament runout sensor 3d models

Stig_ designed a great housing for a filament run-out sensor (https://www.thingiverse.com/thing:2443425). My only issue was with the LED light that would shine when filament is in the sensor. So I have filled the unused/light-emitting holes and...

Sensor de filamento con optoacoplador.

This is my filament sensor remix for [these switches from Amazon](https://www.amazon.com/dp/B00MFRMFS6/ref=cm_sw_su_dp). I also enlarged the filament hole to fit a length of 4mm PFTE tube, which should give a very smooth filament path, and it plugs...

Well I made a simple little Filament motion sensor. It is not complicated and all its elements can be printed with ease. I personally printed the wheels with a layer thickness of 0.1mm using PETG material, which proved to be an excellent choice. The...

Filament loaded was a pain as the filament was not supported well passing through the device So the major change was to use orings as the friction for the filament. The filament rides on top of 2 orings that are next to each other providing a perfect...

This sensor is compatible with a BMG dual drive (clone), as demonstrated in the image, but it should work seamlessly with any setup that features a Bowden tube for filament management. The closer the release point is to the Hotend, the less material...

This ferrule adapter will help guide your filament into the extruder after the filament sensor. I replaced my PTFE tube with newer tubing that was a little bit smaller outer diameter so may have to adjust size by 5% increments in scale up or down.

... ...Thanks to this solution, the filament does not scar during withdrawal.The original case does not have the option of fitting a guide tube, and in my case the "sharp" edge blocked the filament. ... It also contains space for a sponge or cleaning felt.

I bought a filament sensor but because I had a direct drive, I needed to mount it in a different place. Figured I'd share this in case someone else wanted to mount it on the top bar like I did. ...I'll post pics soon!

Just a little mount for the Ender 5+ to relocate the sensor. ...So getting to the back of my Ender 5+ to swap out and feed the filament was a pain, even when it wasn't a direct drive. ...I made this little part to bring it around the side.

Threw together a flat mounting bracket for the sensor so it's closer to the extruder, causing less filament to be unloaded and go to waste. ...At 100% infill it seems sturdy enough to do the job, may add a stiffener on the bottom side if it starts to...

... sensor. ...So getting to the back of my Ender 5+ to swap out and feed the filament was a pain, even when it wasn't a direct drive. I made this little part to bring it around the side. ...The holes are all able to tap so I didn't design tapped holes.

... sensor. ...So getting to the back of my Ender 5+ to swap out and feed the filament was a pain, even when it wasn't a direct drive. I made this little part to bring it around the side. ...The holes are all able to tap so I didn't design tapped holes.

It effectively detects when filament runs out during printing.\r\n\r\nhttps://www.youtube.com/watch?v=4-oLVpIYh2k\r\n\r\nPosition this mounting right before the extruder so the extruder can easily unload filament once it is empty.\r\n\r\nWe developed...

I've created this filament run-out sensor using your choice of filament and just two strips of aluminum can. I haven't tested it yet, but it should work as long as the aluminum is free of any paint or plastic coating. Two strips of roughly 3.25mm...

I was unable to find a filament sensor that matched the size of my micro switch, which measured 12.9mm x 6.5mm x 5.9mm using my calipers. All available sensors were too large. In response, I quickly created my own sensor. I designed it with a cover...

This is my filament sensor remix for these switches from Amazon. I also enlarged the filament hole to fit a length of 4mm PFTE tube, which should give a very smooth filament path, and it plugs nicely into my reverse Bowden mount. ...Just carve out in...

I made my version of a simple and small filament movement sensor based on a magnetic encoder (AS5600) and a toothed bearing from an update for the Titan Aero Extruder Arm. The sensor turned out to be quite compact, perfectly fixes the thread so as...

You need -two M3x20 cylinder head screws to fasten the sensor to the bracket.

I created this to get the filament sensor working on my R17. It's a simple setup and I didn't use any bowden couplings to secure the hose. Instead, I cutted the bowden hose about 70-80mm below the extruder and pushed both ends into the plastic part....

this is the sensor inside... ... https://www.ebay.it/itm/Finecorsa-ottico-end-stop-con-cavo-stampante-stampa-3D-printer-prusa-CNC-mendel/222448606842?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649

I have remixed this excellent Smart sensor design to fit on an Ender 3 V2 modified for Direct Drive inside a Lack enclosure. ... Changes: * Made the housing in two parts to make assembly easier * Added a mounting bracket to screw into a T-Nut in the...

I'm getting a reading from the sensor inside. I've got the link to check out. ...It's over on eBay, where you can find this Finecorsa optical end stop with a printed cable for 3D printing, Prusa, CNC, or Mendel machines.

This version is a remix inspired by the design at https://www.thingiverse.com/thing:2289476 created by mariors50, incorporating a new feature that allows for the detection of excess diameter and folds in the filament. These issues often occur towards...

A small end-of-filament optical detector, which operates with basic functionality, employs two microtubes of PTFE (preferably Capricorn) along with the most flexible pen spring possible. The more flexible it is, the less it will impede the passage...

After seeing the design in http://www.thingiverse.com/thing:1646220 i set myself to remix it to add the following Bracket to mount it to my frame Oil can to lubricate filament as it passes through ... Just enable the setting in marlin and connect...

- Touch sensor Z axis: Part of a mechanism that uses touch sensors as controls, possibly for 3D printing or CNC machines. - Vise for Proxxon MF70: A custom vise designed to work with a specific type of power tool. - Studio lighting for macro...

This is a remix from thing 2577717, modded for fitting bowden tubes on both ends, specially if fitting on top of the extruder. Print instructionsCategory: 3D Printer Parts Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No...

I would print at 100% infill and then drill the filament path to smooth it out so the filament does not catch on the layers. You can create a mount and use longer screws. If you are using the terminal connection version I would place it in the case...

Next up was an oil can designed specifically for lubricating the filament as it passes through various mechanisms. To get everything up and running smoothly, all you need to do is enable the relevant setting in your Marlin software and connect to...